2014 Hilux · Service Manual ENGINE

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
DTC No.
DTC Detection Conditions
Trouble Areas
P0617
When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)
  1. (a) Vehicle speed 20 km/h (12.4 mph) or more
  2. (b) Engine speed 1,000 rpm or more
  3. (c) STA signal ON
  1. Park/Neutral Position (PNP) switch (A/T model)
  2. ST relay circuit
  3. Ignition switch
  4. ECM

WIRING DIAGRAM

A228261E12

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
    If the engine will not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.

    OK:
    Ignition Switch Positions
    Starter Signal
    ON
    OFF
    START
    ON

    Result:
    Result
    Proceed to
    OK
    A
    NG
    B (M/T Model)
    NG
    C (A/T Model)



A
CHECK FOR INTERMITTENT PROBLEMS (Click here)

B
Go to step 5
C


2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
A093221E10
  1. Disconnect the N8 PNP switch connector.

  1. Measure the resistance when the transmission gear selector lever is moved to each position.

    Standard resistance:
    Gear Selector
    Lever Position
    Tester Connection
    Specified Condition
    Except P and N
    4 - 5
    10 kΩ or higher
    P
    2 - 5
    10 kΩ or higher
    R
    N
    D
    2
    L

  1. Reconnect the PNP switch connector.



OK
Go to step 5
NG


3. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Replace the Park/Neutral position switch assembly (Click here).

NEXT


4. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.

    OK:
    Ignition Switch Positions
    Starter Signal
    ON
    OFF
    START
    ON



OK
SYSTEM OK
NG


5. INSPECT IGNITION SWITCH ASSEMBLY
A112426E03
  1. Disconnect the I6 ignition switch connector.

  1. Measure the resistance of the ignition switch.

    Standard resistance:
    Tester Connection
    Ignition Switch Position
    Specified Condition
    AM2 (5) - ST2 (7)
    OFF
    10 kΩ or higher
    AM2 (5) - ST2 (7)
    START
    Below 1 Ω

  1. Reconnect the ignition switch connector.



OK
Go to step 7
NG


6. REPLACE IGNITION SWITCH ASSEMBLY

NEXT


7. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Starter Signal.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.

    OK:
    Ignition Switch Positions
    Starter Signal
    ON
    OFF
    START
    ON



OK
SYSTEM OK
NG


8. REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - STA TERMINAL OF ECM)

NEXT


9. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Clear DTCs (Click here).

  1. Drive the vehicle at more than 20 km/h (12.43 mph) for over 20 seconds.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0617
    A
    No DTC
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)


← P0617 Starter Relay Circuit High (Aug 2012 – Jul 2013)P0617 Starter Relay Circuit High (from Aug 2014) →