2014 Hilux · Service Manual ENGINE

ECM Power Source Circuit

Circuit diagnosis · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the ignition switch is turned ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes a current to flow to the coil, closing the contacts of the MAIN relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A159339E01

INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs initialization (Click here).


1. CHECK ECM (+B VOLTAGE)

  1. A080463E28
    Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (E5-1) - E1 (E7-7)
    11 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
NG


2. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

  1. A065745E92
    Disconnect the E7 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E1 (E7-7) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK ECM (IGSW VOLTAGE)

  1. A080463E29
    Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    IGSW (E5-9) - E1 (E7-7)
    11 to 14 V



OK
Go to step 6
NG


4. INSPECT FUSE (IGN FUSE)

  1. A155929E01
    Remove the IGN fuse from the instrument panel J/B.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


5. INSPECT IGNITION SWITCH ASSEMBLY

  1. A056879E52
    Disconnect the I6 ignition switch connector.

  1. Measure the resistance of the ignition switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (AM2) - 6 (IG2)
    LOCK
    10 kΩ or higher
    5 (AM2) - 6 (IG2)
    ON
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK


6. CHECK ECM (MREL VOLTAGE)

  1. A080463E30
    Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    MREL (E5-8) - E1 (E7-7)
    11 to 14 V



NG
REPLACE INTEGRATION NO.1 RELAY (Click here)
OK


7. INSPECT FUSE (EFI FUSE)

  1. A159237E01
    Remove the EFI fuse from the engine room junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


8. INSPECT INTEGRATION NO.1 RELAY (MAIN RELAY)

  1. G039047E14
    Remove the integration relay from the engine room junction block (Click here).

  1. Measure the voltage of the integration relay

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1J-4 - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPLACE INTEGRATION NO.1 RELAY (Click here)
OK


9. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY (MAIN RELAY) - ECM)

  1. G034918E07
    Disconnect the 1J integration relay connector from the engine room J/B (Click here).

  1. Disconnect the E5 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (check for open):
    Tester Connection
    Specified Condition
    1J-4 - +B (E5-1)
    Below 1 Ω

    Standard resistance (check for short):
    Tester Connection
    Specified Condition
    1J-4 or +B (E5-1) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY (MAIN RELAY) - ECM)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (+B TERMINAL OF ECM - BATTERY POSITIVE TERMINAL)


← Turbocharger Noise (from Aug 2014)ECM Power Source Circuit (Aug 2012 – Jul 2013) →