DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2012
Versions by build date: Jun 2011 – Jul 2012 from Aug 2012
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Data List.
According to the display on the tester, read the Data List.
ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
SPD (SP2)
Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed)
-
SPD (NT)
Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
Lock-up: - ON (after warming up engine): Input turbine speed (NT) equal to engine speed
- OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
The data is displayed in increments of 50 rpm.
Neutral Position SW Signal
PNP switch status/
ON or OFF
Shift lever: - In P or N: ON
- Not in P or N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Stop Light Switch
Stop light switch status/
ON or OFF
Brake pedal: - Depressed: ON
- Released: OFF
-
Shift Status
TCM gear shift command/
1st, 2nd, 3rd, 4th or 5th
Shift lever: - In D: 1st, 2nd, 3rd, 4th or 5th
- In S: 1st, 2nd, 3rd, 4th or 5th
-
Shift SW Status (R Range)
PNP switch status/
ON or OFF
Shift lever: - In R: ON
- Not in R: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (D Range)
PNP switch status/
ON or OFF
Shift lever: - In D: ON
- Not in D: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (4 or D)
PNP switch status/
ON or OFF
Shift lever: - In 4 or D: ON
- Not in 4 or D: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (3 Range)
PNP switch status/
ON or OFF
Shift lever: - In 3: ON
- Not in 3: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (2 Range)
PNP switch status/
ON or OFF
Shift lever: - In 2: ON
- Not in 2: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (L Range)
PNP switch status/
ON or OFF
Shift lever: - In L: ON
- Not in L: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
A/T Oil Temperature 1
No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
- After stall test: Approximately 80°C (176°F)
- With engine cold: Equal to ambient temperature
If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.
A/T Oil Temperature 2
No. 2 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
- After stall test: Approximately 80°C (176°F)
- With engine cold: Equal to ambient temperature
If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted.
Lock Up
Lock-up/
ON or OFF
Lock-up: - Operating: ON
- Not operating: OFF
-
Lock Up Solenoid Status
Lock-up solenoid status/
ON or OFF
Lock-up solenoid: - Operating: ON
- Not operating: OFF
-
SLU Solenoid Status
Shift solenoid valve SLU status/
ON or OFF
Shift solenoid valve SLU: - Operating: ON
- Not operating: OFF
-
SLT Solenoid Status
Shift solenoid valve SLT status/
ON or OFF
- Accelerator pedal depressed: OFF
- Accelerator pedal released: ON
-
- ON (after warming up engine): Input turbine speed (NT) equal to engine speed
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the tester, perform the Active Test.
ECT Tester Display
Test Part
Control Range
Diagnostic Note
Activate the Solenoid (SLU)
Operate shift solenoid valve SLU
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (SLT)*
Operate shift solenoid valve SLT and raise line pressure
ON or OFF - HINT:
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
- ON: No action (normal operation)
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
[Vehicle Condition] - The vehicle is stopped.
- The engine is idling.
Activate the Solenoid (S1)
Operate shift solenoid valve S1
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (S2)
Operate shift solenoid valve S2
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Lock Up
Control shift solenoid valve SLU to set automatic transmission to lock-up condition
ON or OFF
It is possible to check the shift solenoid valve SLU operation.
[Vehicle Condition]- The throttle valve opening angle is less than 35%.
- The vehicle speed is 60 km/h (37 mph) or more.
Control the Shift Position
Operate shift solenoid valve and set each shift position
- Press "→" button: Shift up
- Press "←" button: Shift down
It is possible to check the operation of the shift solenoid valves.
[Vehicle Condition]
The vehicle speed is 50 km/h (31 mph) or less.
Activate the Solenoid (SR)
Operate shift solenoid valve SR
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (SL1)
Operate shift solenoid valve SL1
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
Activate the Solenoid (SL2)
Operate shift solenoid valve SL2
ON or OFF
[Vehicle Condition] - The engine is stopped.
- The shift lever is in P or N.
- HINT:
- *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and hydraulic test are different.
- The engine is stopped.