DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2012
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Data List.
According to the display on the tester, read the Data List.
ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed/
Min.: 0 rpm
Max.: 16383.75 rpm
Engine idling: 700 to 800 rpm
-
Engine Run Time
Engine run time/
Min.: 0 seconds,
Max.: 65535 seconds
Time after engine start
-
Battery Voltage
Battery voltage/
Min.: 0 V
Max.: 65.535 V
Engine idling: 11 to 14 V
-
Starter Signal
Starter signal/
ON or OFF
- ON: Engine cranking
- OFF: Engine not cranking
-
Neutral Position SW Signal
PNP switch status/
ON or OFF
- Shift lever in P or N: ON
- Shift lever not in P or N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Stop Light Switch
Stop light switch status/
ON or OFF
- Brake pedal is depressed: ON
- Brake pedal is released: OFF
-
Check Mode
Check mode/
ON or OFF
ON: Check mode ON
-
SPD Test Result
Check mode result for vehicle/
Compl or Incmpl
-
-
Complete Parts Monitor
Comprehensive component monitor/
Not Avl or Avail
-
-
Fuel System Monitor
Fuel system monitor/
Not Avl or Avail
-
-
Misfire Monitor
Misfire monitor/
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor/
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor/
Compl or Incmpl
-
-
O2S(A/FS) Heater Monitor
Heated oxygen sensor (air fuel ratio sensor) heater monitor/
Not Avl or Avail
-
-
O2S(A/FS) Heater Monitor
Heated oxygen sensor (air fuel ratio sensor) heater monitor/
Compl or Incmpl
-
-
O2S(A/FS) Monitor
Heated oxygen sensor (air fuel ratio sensor) monitor/
Not Avl or Avail
-
-
O2S(A/FS) Monitor
Heated oxygen sensor (air fuel ratio sensor) monitor/
Compl or Incmpl
-
-
A/C Monitor
A/C monitor/
Not Avl or Avail
-
-
A/C Monitor
A/C monitor/
Compl or Incmpl
-
-
2nd Air Monitor
2nd air monitor/
Not Avl or Avail
-
-
2nd Air Monitor
2nd air monitor/
Compl or Incmpl
-
-
EVAP Monitor
EVAP monitor/
Not Avl or Avail
-
-
EVAP Monitor
EVAP monitor/
Compl or Incmpl
-
-
Heated Catalyst Monitor
Heated catalyst monitor/
Not Avl or Avail
-
-
Heated Catalyst Monitor
Heated catalyst monitor/
Compl or Incmpl
-
-
Catalyst Monitor
Catalyst monitor/
Not Avl or Avail
-
-
Catalyst Monitor
Catalyst monitor/
Compl or Incmpl
-
-
# Codes (Include History)
Number of Codes/
Min.: 0
Max.: 255
-
Number of stored DTCs
MIL
MIL status/
ON or OFF
ON: MIL ON
-
Time after DTC Cleared
Time after DTC cleared/
Min.: 0 minutes,
Max.: 65535 minutes
Equivalent to time after DTCs cleared
-
Distance from DTC Cleared
Distance after DTC cleared/
Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile)
Equivalent to distance driven after DTCs cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared/
Min.: 0, Max.: 255
-
Number of warm-up cycles after DTCs cleared
Number of Emission DTC
Number of emission DTCs
-
-
Model Code
Model Code/
-
-
Engine Type
Engine Type/
-
-
Cylinder Number
Cylinder number/
-
-
Destination
Destination/
-
-
Model Year
Model year/
-
-
Engine Speed from EFI
Engine speed/
Min.: 0 rpm
Max.: 16383.75 rpm
- 50 to 400 rpm: Cranking
- 700 to 800 rpm: Idling with warm engine
Engine speed received from the ECM.
Intake-Air Temp from EFI
Intake air temperature/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
Equivalent to temperature at location of mass air flow meter
Intake air temperature received from the ECM.
Coolant Temp from EFI
Engine coolant temperature/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
After warming up engine: 70 to 90°C (158 to 194°F)
Coolant temperature received from the ECM.
Accel Position from EFI
Absolute accelerator pedal position/
Min.: 0%
Max.: 100%
- Accelerator pedal released:
0%
- Accelerator pedal fully depressed:
100%
Accel Position received from the ECM.
Injection Volume from EFI
Injection volume/
Min.: 0 mm3
Max.: 639.98 mm3
Idling: 3.0 to 10 mm3/st
Injection Volume received from the ECM.
SPD (NC0)
Input turbine speed/
Min.: 0 rpm
Max.: 12750 rpm
- Lock-up ON (warmed up engine, other than 4th):
Input turbine speed (NC0) is equal to the engine speed
- Lock-up ON (warmed up engine, 4th):
Input turbine speed (NC0) is 0 rpm
- Lock-up OFF (idling with shift lever in N):
Input turbine speed (NC0) is nearly equal to engine speed
-
SPD (SP2)
Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph)
(output shaft speed is equal to vehicle speed)
-
Shift SW Status (R Range)
PNP switch status/
ON or OFF
- Shift lever in R: ON
- Shift lever not in R: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (2 Range)
PNP switch status/
ON or OFF
- Shift lever in 2: ON
- Shift lever not in 2: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (L Range)
PNP switch status/
ON or OFF
- Shift lever in L: ON
- Shift lever not in L: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (N, P Range) Supported
Status of PNP switch (N or P) supported/
Supp or Unsupp
-
-
Shift SW Status (N, P Range)
PNP switch status/
ON or OFF
- Shift lever not in P or N: ON
- Shift lever in P or N: OFF
-
Shift SW Status (D Range)
PNP switch status/
ON or OFF
- Shift lever in D or 3: ON
- Shift lever not in D or 3: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (3 Range)
PNP switch status/
ON or OFF
- Shift lever in 3: ON
- Shift lever not in 3: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
A/T Oil Temperature 3
ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
- After stall test:
Approximately 80°C (176°F)
- Equal to ambient temperature during engine is cold
If value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor circuit is opened or short circuited
Lock Up
Lock-up/
ON or OFF
- ON: Lock-up operating
- OFF: Lock-up not operating
-
Lock Up Solenoid Status
Lock-up solenoid status/
ON or OFF
- Lock-up: ON
- Not on lock-up: OFF
-
Shift Status
TCM gear shift command/
1st, 2nd, 3rd or 4th
Shift lever position is: - On L: 1st
- On 2: 1st or 2nd
- On 3: 1st, 2nd or 3rd
- On D: 1st, 2nd, 3rd or 4th
-
SLT Solenoid Status
Shift solenoid SLT status/
ON or OFF
- Accelerator pedal is depressed: OFF
- Accelerator pedal is released: ON
-
- ON: Engine cranking
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the tester, perform the Active Test.
ECT Tester Display
Test Part
Control Range
Diagnostic Note
Connect the TC and TE1
Turn on and off TC and TE1 connection
ON or OFF
-
Activate the Solenoid (SLT)*
Operate shift solenoid valve SLT and raise line pressure
ON or OFF - HINT:
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
- ON: No action (normal operation)
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
[Vehicle Condition] - Vehicle stopped
- Engine idling
Activate the Solenoid (S1)
Operate shift solenoid valve S1
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Solenoid (S2)
Operate shift solenoid valve S2
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Lock Up
Control shift solenoid valve SL to set automatic transmission to lock-up
ON or OFF
Possible to check shift solenoid valve SL operation.
[Vehicle Condition]- Throttle valve opening angle: Less than 35%
- Vehicle speed: 60 km/h (37 mph) or more
Activate the Solenoid (SL)
Operate shift solenoid valve SL
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Control the Shift Position
Operate shift solenoid valves and set each shift position
- Press "→" button: Shift up
- Press "←" button: Shift down
Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (31 mph) or less
- HINT:
- *: "Activate the Solenoid (SLT)" in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.