2014 Hilux · Service Manual TRANSMISSION

P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

Diagnostic trouble codes · Vehicles built from Aug 2012

DESCRIPTION

C237837E01
Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The TCM adjusts the current of shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.
DTC Code
DTC Detection Condition
Trouble Area
P2716
Open or short is detected in the shift solenoid valve SLT circuit for 1 second or more while driving (1-trip detection logic).
  1. Open or short in shift solenoid valve SLT circuit
  2. Shift solenoid valve SLT
  3. TCM

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the TCM interprets this as a fault. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C214969E18

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)

  1. C214964E04
    Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (SLT+) - 6 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    2 (SLT+) - Body ground
    Always
    10 kΩ or higher
    6 (SLT-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

  1. C274533E33
    Disconnect the TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T19-20 (SLT+) - T19-19 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    T19-20 (SLT+) - Body ground
    Always
    10 kΩ or higher
    T19-19 (SLT-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to TCM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM

3. INSPECT SHIFT SOLENOID VALVE SLT

  1. C209928E03
    Remove shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 2
    2. Battery negative (-) → Terminal 1
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SLT)


NG
REPLACE SHIFT SOLENOID VALVE SLT
OK

REPAIR OR REPLACE TRANSMISSION WIRE


← P0976 Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2) (+ P0977) (from Aug 2012)P2769 Torque Converter Clutch Solenoid Circuit Low (Shift Solenoid Valve SL) (+ P2770) (from Aug 2012) →