P2769 Torque Converter Clutch Solenoid Circuit Low (Shift Solenoid Valve SL)
Diagnostic trouble codes · Vehicles built from Aug 2012
Also covers:
- P2770 Torque Converter Clutch Solenoid Circuit High (Shift Solenoid Valve SL)
DESCRIPTION
The shift solenoid valve SL is turned on and off by signals from the TCM to control the hydraulic pressure acting on the lock-up relay valve, which then controls the operation of the lock-up clutch.| DTC Code |
DTC Detection Condition |
Trouble Area |
| P2769 |
TCM detects short in shift solenoid valve SL circuit (once) when shift solenoid valve SL is operated (1-trip detection logic) |
|
| P2770 |
TCM detects open in shift solenoid valve SL circuit (once) when shift solenoid valve SL is not operated (1-trip detection logic) |
|
If the TCM detects a malfunction, it turns the shift solenoid valve SL off.
MONITOR DESCRIPTION
Torque converter lock-up is controlled by the TCM based on engine rpm, engine load, engine temperature, vehicle speed, transmission temperature, and shift position selection. The TCM determines the lock-up status of the torque converter by comparing the engine rpm (NE) to the input rpm (NC0). The TCM calculates the actual transmission gear by comparing the input rpm (NC0) to the output rpm (SP2). When conditions are appropriate, the TCM requests "lock-up" by applying control voltage to the shift solenoid valve SL. When the shift solenoid valve SL is opened, the shift solenoid valve SL applies pressure to the lock-up relay valve and locks the torque converter assembly. If the TCM detects an open or short in the shift solenoid valve SL circuit, the TCM interprets this as a fault in the shift solenoid valve SL or its circuit. The TCM will illuminate the MIL and store a DTC.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL) |
Disconnect the transmission wire connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
7 (SL) - Body ground
20°C (68°F)
11 to 15 Ω
Text in Illustration *a
Component without harness connected
(Transmission Wire)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL - TCM) |
Disconnect the TCM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
T19-16 (SL) - Body ground
20°C (68°F)
11 to 15 Ω
Text in Illustration *a
Rear view of wire harness connector
(to TCM)
|
|
||||
| OK | ||
| ||
| 3. INSPECT SHIFT SOLENOID VALVE SL |
Remove shift solenoid valve SL.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Shift solenoid valve SL connector terminal - Shift solenoid valve SL body
20°C (68°F)
11 to 15 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) → Shift solenoid valve SL connector
- Battery negative (-) → Shift solenoid valve SL body
Valve moves and makes an operating noise
- Battery positive (+) → Shift solenoid valve SL connector
| *a |
Component without harness connected (Shift Solenoid Valve SL) |
|
|
||||
| OK | ||
| ||
