2014 Hilux · Service Manual TRANSMISSION

P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU)

Diagnostic trouble codes · Vehicles built from Jun 2011

DESCRIPTION

The TCM uses the signals from the throttle position sensor, air-flow meter, turbine (input) speed sensor, output speed sensor and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.
C159072E01
Then the TCM compares the engagement condition of the lock-up clutch with the lock-up schedule in the TCM memory to detect mechanical problems with the shift solenoid valve SLU, valve body and torque converter clutch.
DTC Code
DTC Detection Condition
Trouble Area
P2757
Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up remains ON in the lock-up OFF range (2 trip detection logic).
  1. Shift solenoid valve SLU remains open or closed
  2. Valve body is blocked
  3. Torque converter clutch
  4. Automatic transmission (clutch, brake or gear, etc.)
  5. Line pressure is too low

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the TCM based on the turbine (input) speed sensor NT, output speed sensor SP2, engine speed, engine load, engine temperature, vehicle speed, transmission temperature, and gear selection. The TCM determines the lock-up status of the torque converter by comparing the engine speed (NE) to the input turbine rpm (NT). The TCM calculates the actual transmission gear by comparing input turbine rpm (NT) to output shaft rpm (SP2). When conditions are appropriate, the TCM requests "lock-up" by applying control voltage to the shift solenoid SLU. When the shift solenoid SLU is turned on, it applies pressure to the lock-up relay valve and locks the torque converter clutch.
If the TCM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the TCM interprets this as a fault in the shift solenoid valve SLU or lock-up system performance.
The TCM will turn on the MIL and store the DTC.
Example:
When either of the following is met, the system judges it as a malfunction.
  1. There is a difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the TCM commands lock-up.
    (Engine speed is at least 70 rpm more than input turbine speed).
  2. There is no difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the TCM commands lock-up off.
    (The difference between engine speed and input turbine speed is less than 35 rpm).

INSPECTION PROCEDURE


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Active Test.

  7. According to the display on the tester, perform the Active Test.

    ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Lock Up
    Control shift solenoid valve SLU to set automatic transmission to lock-up condition
    ON or OFF
    It is possible to check the shift solenoid valve SLU operation.
    [Vehicle Condition]
    1. The throttle valve opening angle is less than 35%.
    2. The vehicle speed is 60 km/h (37 mph) or more.

    HINT:
    1. This test can be conducted when the vehicle speed is 60 km/h (37 mph) or more.
    2. This test can be conducted with the 5th gear.

  8. Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.
    C159073E01

    HINT:
    1. When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.
    2. Slowly release the accelerator pedal in order to decelerate, but do not fully release the pedal (fully releasing the pedal will close the throttle valve and lock-up may be turned off automatically).


1. CHECK DTC OUTPUT (IN ADDITION TO DTC P2757)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / ECT / Trouble Codes.

  1. Read the DTCs using the tester.

    Result 
    Result
    Proceed to
    Only P2757 is output
    A
    P2757 and other DTCs are output
    B

    HINT:
    If any other codes besides "P2757" are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2. INSPECT SHIFT SOLENOID VALVE SLU

  1. C162477E02
    Remove the shift solenoid valve SLU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 2
    2. Battery negative (-) → Terminal 1
    Valve moves and makes an operating noise



NG
REPLACE SHIFT SOLENOID VALVE SLU
OK


3. INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly.

    OK:
    There are no foreign objects on any valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK


4. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Check the torque converter clutch assembly.

    OK:
    The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY


← P2740 Transmission Fluid Temperature Sensor "B" Circuit (+ P2742, P2743) (from Jun 2011)P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) (from Jun 2011) →