2014 Hilux · Service Manual TRANSMISSION

P0985 Shift Solenoid "E" Control Circuit Low (Shift Solenoid Valve SR)

Diagnostic trouble codes · Vehicles built from Jun 2011

Also covers:

DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2 and SR, which is controlled by the TCM. If an open or short circuit occurs in the shift solenoid valves, the TCM controls the remaining normal shift solenoid valve to allow the vehicle to be operated safely (Click here).
DTC Code
DTC Detection Condition
Trouble Area
P0985
TCM detects short in solenoid valve SR circuit 2 times when solenoid valve SR is operated (1 trip detection logic)
  1. Short in shift solenoid valve SR circuit
  2. Shift solenoid valve SR
  3. TCM
P0986
TCM detects open in solenoid valve SR circuit 2 times when solenoid valve SR is not operated (1 trip detection logic)
  1. Open in shift solenoid valve SR circuit
  2. Shift solenoid valve SR
  3. TCM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve SR circuit. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem and illuminates the MIL and stores the DTC. When the shift solenoid valve SR is ON, if resistance is 8 Ω or less, the TCM determines that there is a short in the shift solenoid valve SR circuit.
When the shift solenoid valve SR is OFF, if resistance is 100 kΩ or more, the TCM determines that there is an open in the shift solenoid valve SR circuit (Click here).

WIRING DIAGRAM

C161204E52

INSPECTION PROCEDURE


HINT:
The shift solenoid valve SR turns ON/OFF normally when the shift lever is on D:
TCM gear shift command
1st
2nd
3rd
4th
5th
Shift solenoid valve SR
OFF
OFF
OFF
OFF
ON


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SR)

  1. C159421E50
    Disconnect the E1 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    7 - Body ground
    20°C (68°F)
    11 to 15 Ω



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

  1. C191544E29
    Disconnect the T19 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T19-16 (SR) - Body ground
    20°C (68°F)
    11 to 15 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM

3. INSPECT SHIFT SOLENOID VALVE SR

  1. A110988E08
    Remove the shift solenoid valve SR.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve SR connector terminal - Shift solenoid valve SR body
    20°C (68°F)
    11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve SR connector
    2. Battery negative (-) → Shift solenoid valve SR body
    Valve moves and makes an operating noise



NG
REPLACE SHIFT SOLENOID VALVE SR
OK

REPAIR OR REPLACE TRANSMISSION WIRE


← P0976 Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2) (+ P0977) (from Jun 2011)P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (Jun 2011 – Jul 2012) →