FREEZE FRAME DATA
Troubleshooting · Vehicles built from Jun 2011
| FREEZE FRAME DATA |
Whenever a DTC is stored, the skid control ECU (brake actuator assembly) stores the current vehicle state as freeze frame data.
The skid control ECU (brake actuator assembly) stores the number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the ABS/VSC was activated.
- HINT:
- If the vehicle is stopped or traveling at a low speed (7 km/h (4 mph) or less), or if a DTC is stored, the skid control ECU (brake actuator assembly) stops counting the number of times the ignition switch has been turned from off to ON.
- Freeze frame data at the time the ABS/VSC operates:
The skid control ECU (brake actuator assembly) stores and updates data whenever the ABS/VSC operates.
When the ECU stores data at the time a DTC is stored, the data stored during ABS/VSC operation is cleared.
- Freeze frame data at the time a DTC is stored:
When the skid control ECU (brake actuator assembly) stores data at the time a DTC is stored, no updates are performed until the data is cleared.
- If the vehicle is stopped or traveling at a low speed (7 km/h (4 mph) or less), or if a DTC is stored, the skid control ECU (brake actuator assembly) stops counting the number of times the ignition switch has been turned from off to ON.
| CHECK FREEZE FRAME DATA |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / DTC.
According to the display on the intelligent tester, select the trouble code data with freeze frame data.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Elapsed Time after Freeze Trigger
Elapsed time after freeze trigger / Min.: 0 msec, Max.: 500 msec
-
-
Number of IG ON
Number of times ignition switch turned to ON after storing freeze frame data / 0 to 31
-
-
Stop Light SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW
Parking brake switch / ON or OFF
ON: Parking brake applied
OFF: Parking brake released
-
Gear Position
Gear position information / P,N, R, 1st-8th, Fail or Not R
Actual gear position
-
Shift Lever Position
Shift lever position information / P,N, R, D/M, 1st-6th/B or Fail
Actual shift lever position
-
Operated System
Operated system status / ABS, VSC, TRC, BA, HAB, PBA, PB, HA-CTRL, TSC, Fail, Sys or Non
-
ABS: ABS is activated.
VSC: VSC is activated.
TRC: TRC is activated.
BA: BA is activated.
HAB: High power assist brake* is activated.
Fail: Fail-safe mode is activated.
Non: No operation is activated.
Master Cylinder Sensor
Master cylinder pressure sensor reading / Min.: 0.00 V, Max.: 5.00 V
When brake pedal released: 0.3 to 0.9 V
The value increases when the brake pedal is depressed.
M/C Sensor Grade
Master cylinder pressure sensor change / Min.: -30 MPa/s, Max.: 225 MPa/s
When brake pedal released or pedal held at constant position: 0 MPa/s
Changes in proportion to the pedal movement speed when the brake pedal is being operated.
Yaw Rate Sensor
Yaw rate sensor / Min.: -128°/s, Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Lateral G
Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
Changes in proportion to acceleration during turning.
Forward and Rearward G
Forward and backward G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
Changes in proportion to acceleration during acceleration/deceleration.
FR Wheel Speed
Front speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
FL Wheel Speed
Front speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
RR Wheel Speed
Rear speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
RL Wheel Speed
Rear speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
Vehicle Speed
Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
No large fluctuations when driving at a constant speed.
Vehicle Speed Grade
Vehicle acceleration / Min.: -25.10 m/s2, Max.: 24.90 m/s2
Vehicle stopped: 0 m/s2
Changes in proportion to vehicle acceleration/deceleration during driving.
Real Engine Torque
Actual engine torque / Min.: -1024.0 Nm, Max.: 1023.0 Nm
-
-
Accelerator Opening Angle %
Throttle valve opening amount / Min.: 0.0%, Max.: 128.0%
When accelerator pedal released: 0%
Changes in proportion to the movement of the pedal during accelerator pedal operation.
Brake Pedal Load Sensing SW
Brake pedal load sensing switch / ON or OFF
ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point
-
Inspection Mode
Inspection mode / Other or Inspect
Other: Normal mode
Inspect: Inspection mode
-
Steering Angle Sensor
Steering angle sensor / Min.: -3276.8°, Max.: 3276.7°
Left turn: Increases
Right turn: Decreases
-
TRC/VSC Off Mode
TRC/VSC off mode / Normal, TRC OFF or VSC OFF
Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: TRC, VSC off mode
-
- *: This function provides an assist in addition to that of the brake assist function when the driver requests a large amount of braking force.
- *: This function provides an assist in addition to that of the brake assist function when the driver requests a large amount of braking force.
| CLEAR FREEZE FRAME DATA |
- NOTICE:
- Clearing the DTC also clears the freeze frame data.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Clear the DTCs (Click here).