C1210 Zero Point Calibration of Yaw Rate Sensor Undone
Diagnostic trouble codes · Vehicles built Nov 2011 – Mar 2012
Also covers:
- C1336 Zero Point Calibration of Acceleration Sensor Undone
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The skid control ECU (brake actuator assembly) receives signals from the yaw rate sensor assembly via the CAN communication system.The yaw rate sensor assembly has a built-in acceleration sensor.
If there is trouble in the bus lines between the yaw rate sensor assembly and the CAN communication system, DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) are stored.
DTC C1210 and C1336 are also stored when calibration has not been completed.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1210 |
Zero point calibration of the yaw rate sensor is incomplete. |
|
| C1336 |
Zero point calibration of the acceleration sensor is incomplete. |
|
INSPECTION PROCEDURE
- NOTICE:
- After replacing the brake actuator assembly and/or yaw rate sensor assembly, perform calibration (Click here).
- HINT:
- When DTC U0123 and/or U0124 is output along with DTC C1210 and/or C1336, inspect and repair trouble areas indicated by DTC U0123 and/or U0124 first (Click here).
| 1. PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR |
Perform zero point calibration of the yaw rate and acceleration sensor (Click here).
| NEXT | |
| 2. PERFORM TEST MODE (SIGNAL CHECK) |
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure (Click here).
- OK:
- All Test Mode DTCs are cleared.
- HINT:
- If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area (Click here).
|
|
||||
| OK | ||
| ||
| 3. CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION |
Turn the ignition switch off.
Check that the yaw rate sensor assembly is installed properly (Click here).
- OK:
- The sensor is tightened to the specified torque.
- The sensor is not installed at an angle.
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (DECELERATION SENSOR / YAW RATE SENSOR) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Deceleration Sensor
Acceleration sensor (GL1) / Min.: -18.525 m/s2, Max.: 18.387 m/s2
-
Changes continuously during acceleration/deceleration.
Deceleration Sensor2
Acceleration sensor (GL2) / Min.: -18.525 m/s2, Max.: 18.387 m/s2
-
Changes continuously during acceleration/deceleration.
Yaw Rate Sensor
Yaw rate sensor / Min.: -128°/s, Max.: 127°/s
Vehicle stationary: 0°/s
Right turn: -128 to 0°/s
Left turn: 0 to 127°/s
-
Check the yaw rate and acceleration sensor output value displayed on the intelligent tester.
- OK:
- The yaw rate and acceleration sensor output value is normal.
Result Result
Proceed to
NG
A
OK
for LHD
B
for RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
