2014 Hilux · Service Manual BRAKE

C1210 Zero Point Calibration of Yaw Rate Sensor Undone

Diagnostic trouble codes · Vehicles built Jun 2011 – Oct 2011

Also covers:

Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate sensor assembly via the CAN communication system.
The yaw rate sensor assembly has a built-in acceleration sensor.
If there is trouble in the bus lines between the yaw rate sensor assembly and the CAN communication system, DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) are stored.
DTC C1210 and C1336 are also stored when calibration has not been completed.
DTC Code
DTC Detection Condition
Trouble Area
C1210
Zero point calibration of the yaw rate sensor is incomplete.
  1. Yaw rate sensor assembly
  2. Skid control ECU (Brake actuator assembly)
C1336
Zero point calibration of the acceleration sensor is incomplete.
  1. Acceleration sensor (Yaw rate sensor assembly)
  2. Skid control ECU (Brake actuator assembly)

INSPECTION PROCEDURE

NOTICE:
After replacing the brake actuator assembly and/or yaw rate sensor assembly, perform calibration (Click here).

HINT:
When DTC U0123 and/or U0124 is output along with DTC C1210 and/or C1336, inspect and repair trouble areas indicated by DTC U0123 and/or U0124 first (Click here).


1. PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
  1. Perform zero point calibration of the yaw rate and acceleration sensor (Click here).


NEXT


2. PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are cleared.

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area (Click here).



NG
Go to step 3
OK

END

3. CHECK YAW RATE SENSOR ASSEMBLY INSTALLATION
  1. Turn the ignition switch off.

  1. Check that the yaw rate sensor assembly is installed properly (Click here).

    OK:
    The sensor is tightened to the specified torque.
    The sensor is not installed at an angle.



NG
INSTALL YAW RATE SENSOR ASSEMBLY CORRECTLY (Click here)
OK


4. READ VALUE USING INTELLIGENT TESTER (DECELERATION SENSOR / YAW RATE SENSOR)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Deceleration Sensor
    Acceleration sensor (GL1) / Min.: -18.525 m/s2, Max.: 18.387 m/s2
    -
    Changes continuously during acceleration/deceleration.
    Deceleration Sensor2
    Acceleration sensor (GL2) / Min.: -18.525 m/s2, Max.: 18.387 m/s2
    -
    Changes continuously during acceleration/deceleration.
    Yaw Rate Sensor
    Yaw rate sensor / Min.: -128°/s, Max.: 127°/s
    Vehicle stationary: 0°/s
    Right turn: -128 to 0°/s
    Left turn: 0 to 127°/s
    -

  1. Check the yaw rate and acceleration sensor output value displayed on the intelligent tester.

    OK:
    The yaw rate and acceleration sensor output value is normal.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    for LHD
    B
    for RHD
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)


← C1203 ECM Communication Circuit Malfunction (from Aug 2013)C1210 Zero Point Calibration of Yaw Rate Sensor Undone (+ C1336) (Nov 2011 – Mar 2012) →