19 (1) Accelerator Position Sensor Circuit Malfunction
Diagnostic trouble codes · Vehicles built Jun 2011 – Oct 2011
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
- HINT:
- This is the repair procedure of "accelerator pedal position sensor".
- This electrical throttle system does not use a throttle cable.
- This accelerator pedal position sensor is a non-contact type.
- This is the repair procedure of "accelerator pedal position sensor".
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for engine control, and the VPA2 is a signal to indicate information about the opening angle which is used for detecting malfunctions. Based on signals input from terminals VPA and VPA2, the ECM judges the current opening angle of the accelerator pedal and controls the injection pump.


| DTC No. |
DTC Detecting Condition |
Trouble Area |
| 19 (1) |
Condition (a), (b), (c) or (d) continues for 2.0 seconds: (a) VPA is less than or equal to 0.2 V, and VPA2 is less than or equal to 0.5 V (b) VPA is greater than or equal to 4.8 V (c) When 3.45 V is greater than or equal to VPA, and VPA is greater than or equal to 0.2 V; and VPA2 is greater than or equal to 4.8 V (d) "VPA minus VPA2" is less than or equal to 0.02 V |
|
| Condition (a) continues for 0.5 seconds: (a) VPA is less than or equal to 0.2 V, or VPA2 is less than or equal to 0.5 V |
- HINT:
- After confirming DTC 19 (1), use the intelligent tester to confirm the throttle valve opening percentage.
| Trouble area |
Accelerator pedal position expressed as voltage |
|||
| Accelerator pedal released |
Accelerator pedal depressed |
|||
| ACCEL POS #1 |
ACCEL POS #2 |
ACCEL POS #1 |
ACCEL POS #2 |
|
| VC circuit open |
0 to 0.2 V |
0 to 0.2 V |
0 to 0.2 V |
0 to 0.2 V |
| VPA circuit open or ground short |
0 to 0.2 V |
1.2 to 2.0 V |
0 to 0.2 V |
3.4 to 5.3 V |
| VPA2 circuit open or ground short |
0.5 to 1.1 V |
0 to 0.2 V |
2.6 to 4.5 V |
0 to 0.2 V |
| E2 circuit open |
4.5 to 5.5 V |
4.5 to 5.5 V |
4.5 to 5.5 V |
4.5 to 5.5 V |
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
When using intelligent tester:
| 1. READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION) |
Connect the intelligent tester to the DLC3.

Turn the ignition switch ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Position.
Check that the value displayed on the intelligent tester changes when repeatedly depressing and releasing the accelerator pedal.
- OK:
- Value changes.
|
|
||||
| OK | |
| 2. READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN) |
Clear the DTC (Click here).
Start the engine.
Idle the engine for 15 seconds or more.
Read the DTC (Click here).
- Result:
Display (DTC output)
Proceed to
DTC 19(1) is output again
A
No DTC output
B
|
|
||||
| A | ||
| ||
| 3. CHECK WIRE HARNESS (ECM - ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the A13 accelerator pedal position sensor connector.

Disconnect the E21 and E22 ECM connectors.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
A13-1 (VCP2) - E22-1 (VC)
Below 1 Ω
A13-2 (EPA2) - E22-9 (E2)
Below 1 Ω
A13-3 (VPA2) - E21-12 (VPA2)
Below 1 Ω
A13-4 (VCPA) - E21-6 (VCPA)
Below 1 Ω
A13-5 (EPA) - E21-4 (EPA)
Below 1 Ω
A13-6 (VPA) - E21-5 (VPA)
Below 1 Ω
A13-1 (VCP2) or E22-1 (VC) - Body ground
10 kΩ or higher
A13-2 (EPA2) or E22-9 (E2) - Body ground
10 kΩ or higher
A13-3 (VPA2) or E21-12 (VPA2) - Body ground
10 kΩ or higher
A13-4 (VCPA) or E21-6 (VCPA) - Body ground
10 kΩ or higher
A13-5 (EPA) or E21-4 (EPA) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK ECM (VC, VCPA VOLTAGE) |
Disconnect the accelerator pedal position sensor connector.

Turn the ignition switch ON.
Measure the voltage of the ECM connector.
- Standard voltage:
Tester Connection
Specified Condition
E22-1 (VC) - E22-9 (E2)
4.5 to 5.5 V
E21-6 (VCPA) - E21-4 (EPA)
4.5 to 5.5 V
|
|
||||
| OK | |
| 5. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
| NEXT | |
| 6. READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN) |
Clear the DTC (Click here).
Start the engine.
Idle the engine for 15 seconds or more.
Read the DTC (Click here).
- Result:
Display (DTC output)
Proceed to
DTC 19(1) is output again
A
No DTC output
B
|
|
||||
| A | ||
| ||
When not using intelligent tester:
| 1. CHECK WIRE HARNESS (ECM - ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the A13 accelerator pedal position sensor connector.

Disconnect the E21 and E22 ECM connectors.
Measure the resistance of the wire harness side connectors.
- Standard resistance :
Tester Connection
Specified Condition
A13-1 (VCP2) - E22-1 (VC)
Below 1 Ω
A13-2 (EPA2) - E22-9 (E2)
Below 1 Ω
A13-3 (VPA2) - E21-12 (VPA2)
Below 1 Ω
A13-4 (VCPA) - E21-6 (VCPA)
Below 1 Ω
A13-5 (EPA) - E21-4 (EPA)
Below 1 Ω
A13-6 (VPA) - E21-5 (VPA)
Below 1 Ω
A13-1 (VCP2) or E22-1 (VC) - Body ground
10 kΩ or higher
A13-2 (EPA2) or E22-9 (E2) - Body ground
10 kΩ or higher
A13-3 (VPA2) or E21-12 (VPA2) - Body ground
10 kΩ or higher
A13-4 (VCPA) or E21-6 (VCPA) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 2. CHECK ECM (VC, VCPA VOLTAGE) |
Disconnect the A13 accelerator pedal position sensor connector.

Turn the ignition switch ON.
Measure the voltage of the ECM connector.
- Standard voltage:
Tester Connection
Specified Condition
E22-1 (VC) - E22-9 (E2)
4.5 to 5.5 V
E21-6 (VCPA) - E21-4 (EPA)
4.5 to 5.5 V
|
|
||||
| OK | |
| 3. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
| NEXT | |
| 4. READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN) |
Clear the DTC (Click here).
Start the engine.
Idle the engine for 15 seconds or more.
Read the DTC (Click here).
- Result:
Display (DTC output)
Proceed to
DTC 19(1) is output again
A
No DTC output
B
|
|
||||
| A | ||
| ||
