P0095 Intake Air Temperature Sensor 2 Circuit
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- P0097 Intake Air Temperature Sensor 2 Circuit Low
- P0098 Intake Air Temperature Sensor 2 Circuit High
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION


The diesel turbo Intake Air Temperature (IAT) sensor is built into the charge air cooler and senses the IAT. A built-in thermistor of the sensor changes the resistance value according to the intake air temperature. The lower the IAT is, the greater the thermistor resistance value becomes, and the higher the temperature is, the lower the resistance value becomes (see Fig. 1).
The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve the driveability with a cold engine.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0095 |
Open or short in diesel turbo IAT sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0097 |
Short in diesel turbo IAT sensor circuit for 0.5 seconds (sensor resistance value less than 25 Ω [sensor output voltage less than 0.05 V]) (1 trip detection logic) |
|
| P0098 |
Open in diesel turbo IAT sensor circuit for 0.5 seconds (sensor resistance value more than 156 kΩ [sensor output voltage more than 4.9 V]) (1 trip detection logic) |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
- NOTICE:
- If the ECM is replaced, the new ECM needs initialization (Click here).
| 1. CHECK ECM (THIA VOLTAGE) |
![]() ![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E8-20 (THIA) - E8-28 (E2)
20°C (68°F)
0.5 to 3.4 V
|
|
||||
| NG | |
| 2. INSPECT DIESEL TURBO INTAKE AIR TEMPERATURE SENSOR |
![]() ![]() |
Remove the sensor.
Measure the resistance of the sensor.
- Standard resistance:
Connection
Specified Condition
20°C (68°F)
2.21 to 2.65 kΩ
- NOTICE:
- When checking the IAT sensor in the water, keep the terminals dry. After the check, wipe the sensor dry.
|
|
||||
| OK | |
| 3. CHECK WIRE HARNESS (ECM - DIESEL TURBO INTAKE AIR TEMPERATURE SENSOR) |
![]() ![]() |
Disconnect the I4 diesel turbo IAT sensor connector.
Disconnect the E8 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
E8-20 (THIA) - I4-2
Below 1 Ω
E8-28 (E2) - I4-1
Below 1 Ω
E8-20 (THIA) or I4-2 - Body ground
10 kΩ or higher
E8-28 (E2) or I4-1 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||



