2014 Hilux · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. INSTALL NO. 1 IDLER PULLEY

A076438E01
  1. Install the idler pulley with the bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    HINT:
    "DOUBLE" is marked on the No. 1 idler pulley to distinguish it from the No.2 idler pulley.


2. INSTALL NO. 2 IDLER PULLEY

NOTICE:
w/o Integrated Type:
The installation of the No. 2 idler pulleys differs depending on the mark on the No. 2 idler pulleys shown in the illustration.
A191316E01

HINT:
Use the same procedure for both No. 2 idler pulleys.

  1. w/ Idler Pulley Cover Plate (PU107013ARMXY3):

    1. A191314E01
      Install the idler pulley cover plate, idler pulley and No. 2 idler pulley cover plate with the bolt.

      Torque:
      54 N*m{ 551 kgf*cm , 40 ft.*lbf }

      NOTICE:
      1. If it is necessary to replace the pulley or either plate, replace the No. 2 idler pulley cover plate, No. 2 idler pulley and idler pulley cover plate as a set with new parts.
      2. When replacing parts, make sure to replace the No. 2 idler pulley with a new pulley marked "PU107013ARMXY3".

  1. w/o Idler Pulley Cover Plate (PU107013ARMXY1):

    1. A191315E01
      Install the idler pulley and No. 2 idler pulley cover plate with the bolt.

      Torque:
      54 N*m{ 551 kgf*cm , 40 ft.*lbf }

      NOTICE:
      1. If it is necessary to replace the pulley or plate, replace both the pulley and plate with a set of new parts that includes a No. 2 idler pulley cover plate, No. 2 idler pulley and idler pulley cover plate.
      2. When replacing parts, make sure to replace the No. 2 idler pulley with a new pulley marked "PU107013ARMXY3".

  1. A076338E01
    for Integrated Type:
    Install the 2 No. 2 idler pulleys with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }


3. INSTALL OIL DIPSTICK GUIDE
  1. Remove the oil dipstick gauge.

  1. Remove the bolt and oil dipstick guide.

  1. Remove the O-ring from the oil dipstick guide.


4. INSTALL SPARK PLUG

5. INSTALL IGNITION COIL
  1. Install the 6 ignition coils with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


6. INSTALL OIL FILLER CAP HOUSING
  1. Install a new gasket and oil filler cap housing with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


7. INSTALL OIL FILLER CAP

8. INSTALL WATER BY-PASS JOINT REAR

A076535E01
  1. Install a new O-ring to the water outlet pipe.

  1. Install 2 new gaskets and the water by-pass joint with the 2 bolts and 4 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for bolts
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for nuts

  1. Connect the engine coolant temperature sensor connector.


9. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE
  1. Install the 2 camshaft timing oil control valves with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


10. INSTALL INTAKE MANIFOLD

A076536E01
  1. Set a new gasket on each cylinder head.

    NOTICE:
    1. Align the port holes of the gasket and cylinder head.
    2. Be careful of the installation direction.

  1. Set the intake manifold on the cylinder heads.

  1. A076533E01
    Install and uniformly tighten the 10 bolts in several passes.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. Connect the 6 fuel injector connectors.


11. INSTALL OIL FILTER BRACKET
  1. Install a new gasket and the oil filter bracket with the 3 bolts and 2 nuts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


12. INSTALL WATER INLET HOUSING

  1. A112082
    Install a new gasket to the water inlet housing with thermostat.

  1. Install the water inlet housing with thermostat with the 3 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


13. INSTALL V-RIBBED BELT TENSIONER

A076445E02
  1. Temporarily install the V-ribbed belt tensioner with the 5 bolts.

  1. Install the V-ribbed belt tensioner by tightening bolt 1 and then bolt 2.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

    HINT:
    Each bolt length is as follows:
    A = 70 mm (2.76 in.)
    B = 33 mm (1.30 in.)


14. INSTALL IDLER PULLEY (w/o Air Conditioning System)
  1. Install the idler pulley with the 3 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


15. INSTALL NO. 1 ENGINE MOUNTING BRACKET FRONT LH
  1. Install the engine mounting bracket with the 3 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


16. INSTALL NO. 1 ENGINE MOUNTING BRACKET FRONT RH
  1. Install the engine mounting bracket with the 4 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


17. INSTALL NO. 2 VENTILATION HOSE

18. INSTALL VENTILATION HOSE

19. INSTALL HEATER WATER HOSE TO ENGINE ASSEMBLY

20. INSTALL NO. 2 RADIATOR HOSE

21. INSTALL NO. 1 RADIATOR HOSE

22. INSTALL ENGINE WIRE TO ENGINE ASSEMBLY

23. INSTALL ENGINE ASSEMBLY
  1. Attach an engine sling device and chain block to the engine hangers.

  1. Remove the engine from the engine stand.

  1. A112951E02
    Slowly lower the engine assembly into the engine compartment.

  1. A112950
    Install the engine mounting brackets to the frame with the 4 bolts and 4 nuts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Remove the 4 bolts and 2 engine hangers.


24. INSTALL FLYWHEEL (for Manual Transmission)

  1. A076326E08
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A076899E01
    Temporarily install the flywheel with 8 new bolts.

  1. Install and tighten the 8 bolts uniformly in several steps.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Mark the top of the bolts with paint.

  1. Tighten the 8 bolts 90° in the same sequence.

  1. Check that the paint marks are now at a 90° angle to the top.


25. INSTALL CLUTCH DISC (for Manual Transmission)

  1. C112690E01
    Insert SST into the clutch disc. Then insert the SST (together with the clutch disc) into the flywheel.
    SST
    09301-00110  

    NOTICE:
    Take care not to insert the clutch disc facing the wrong direction.


26. INSTALL CLUTCH COVER (for Manual Transmission)

  1. D029623E01
    Align the matchmarks on the clutch cover and flywheel.

  1. Tighten the 6 bolts as described below.

    1. Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.

    2. Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.

      Torque:
      19 N*m{ 195 kgf*cm , 14 in.*lbf }

  1. Lightly move SST up and down, and right and left.

    SST
    09301-00110  

  1. Check that the disc is in the center, and then tighten the bolts.


27. INSTALL DRIVE PLATE AND RING GEAR ASSEMBLY (for Automatic Transmission)

  1. A076326E08
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. P000601E01
    Apply adhesive to 2 or 3 threads of the ends of the bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A151280E02
    Install the front spacer, drive plate and rear spacer to the crankshaft.

  1. Install and uniformly tighten the 8 bolts in several steps in the order shown in the illustration.

    Torque:
    83 N*m{ 846 kgf*cm , 61 ft.*lbf }


28. INSTALL MANUAL TRANSMISSION
  1. 2WD:
    Install the manual transmission to the vehicle (Click here).

  1. 4WD:
    Install the manual transmission to the vehicle (Click here).


29. INSTALL AUTOMATIC TRANSMISSION
  1. 2WD:
    Install the automatic transmission to the vehicle (Click here).

  1. 4WD:
    Install the automatic transmission to the vehicle (Click here).


30. INSTALL STARTER

  1. A112759
    Install the starter with the 2 bolts.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }

  1. A112758
    Install the starter wire to terminal 30 with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the starter connector.


31. INSTALL EXHAUST MANIFOLD LH

  1. A076439E01
    Set a new gasket to the LH cylinder head with the oval shape facing backward.

    NOTICE:
    Be careful of the installation direction.

  1. Install the exhaust manifold with the 6 nuts. Uniformly tighten the nuts in several passes.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the A/F sensor connector.


32. INSTALL EXHAUST MANIFOLD RH

  1. A076440E02
    Set a new gasket to the RH cylinder head with the oval shape facing forward.

    NOTICE:
    Be careful of the installation direction.

  1. Install the exhaust manifold with the 6 nuts. Uniformly tighten the nuts in several passes.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the A/F sensor connector.


33. INSTALL FRONT FENDER APRON SEAL UPPER
  1. Install the RH and LH fender apron seals with the 10 clips.


34. INSTALL FRONT FENDER SEAL
  1. Install the RH and LH fender seals with the 10 clips.

  1. Install the front tires.


35. INSTALL FRONT EXHAUST PIPE
  1. Install the front pipe to the pipe support.

  1. Install a new gasket and the front pipe to the exhaust manifold.

  1. Install the front pipe with the 2 nuts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }


36. INSTALL NO. 2 ENGINE WIRE
  1. Connect the No. 2 engine wire to the cylinder block.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


37. INSTALL ENGINE WIRE

  1. G038831E01
    Connect the 2 engine room junction block connectors and attach the wire clamp.

  1. Connect the cable to the engine room junction block with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Attach the 4 claws to install the side relay block cover.

  1. Install the upper relay block cover.

  1. Connect the ground wire with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Connect the ground wire to the frame with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Push the engine wire through the dash panel into the cabin.

  1. Connect the A.D.D. connector.

  1. A191307
    Connect the ECM connectors.

    1. Connect the 5 ECM connectors.

    2. Connect the 4WD control ECU connector.

    3. Install the glove compartment door.

  1. Connect the wire clamp to the engine mounting bracket front LH with the bolt.


38. INSTALL INTAKE AIR SURGE TANK

  1. A075648E01
    Install a new gasket to the intake air surge tank.

  1. Using an 8 mm hexagon socket wrench, install the intake air surge tank with the 4 bolts. Install the 2 nuts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. A076502E01
    Install the 2 surge tank stays with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the oil baffle plate with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A075646E01
    Install the throttle body bracket with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the 3 wire harness clamps and hose clamp.

  1. Connect the throttle body with motor connector.

  1. Connect the 2 VSV connectors.

  1. A075645E01
    Connect the ventilation hose.

  1. A075644E01
    Connect the purge line hose.

  1. A076500E02
    Connect the 2 water by-pass hoses.


39. INSTALL HEATER HOSE

  1. A113356E01
    Connect the hater water inlet hose.

  1. Connect the heater water outlet hose.


40. INSTALL NO. 2 FUEL PIPE

  1. Connect the fuel pipe.

    1. A071366E09
      Check that there is no damage or contamination in the connected part of the pipe.

    2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a little amount of fresh engine oil on the tip of the pipe.

    3. A071366E10
      After having finished the connection, try to pull apart the pipe and the connector and confirm that they are securely connected.

  1. Install the fuel pipe clamp.


41. INSTALL NO. 1 FUEL PIPE

  1. Connect the fuel pipe.

    1. A071366E09
      Check that there is no damage or contamination in the connected part of the pipe.

    2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a little amount of fresh engine oil on the tip of the pipe.

    3. A071366E10
      After having finished the connection, try to pull apart the pipe and the connector and confirm that they are securely connected.

  1. Install the fuel pipe clamp.


42. INSTALL COOLER COMPRESSOR

43. INSTALL GENERATOR

A122806
  1. Install the generator bar with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the generator connector.


44. INSTALL VANE PUMP

A076444E02
  1. Install the vane pump with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Do not hit other parts with the pulley when installing the vane pump.

  1. Connect the oil pressure switch connector.


45. INSTALL FAN PULLEY

46. INSTALL FAN WITH FLUID COUPLING
  1. Temporarily install the fan with fluid coupling with the 4 nuts.


47. INSTALL DRIVE BELT

A076442E01
  1. While turning the belt tensioner counterclockwise, align its holes, and then insert a bar of 6 mm (0.24 in.) into the holes to fix the belt tensioner.

  1. Install the V-ribbed belt.

  1. While turning the belt tensioner counterclockwise, remove the bar.

  1. A113028E02
    If it is hard to install the V-ribbed belt, perform the following procedure.

    1. Put the V-ribbed belt on everything except the P/S pump as shown in the illustration.

    2. While releasing the belt tension by turning the belt tensioner counterclockwise, put the V-ribbed belt on the P/S pump.


48. TIGHTEN FAN WITH FLUID COUPLING

49. INSTALL FAN SHROUD
  1. Set the fan shroud into the engine compartment.

  1. Connect the 2 oil cooler hoses with the hose clamp.


50. INSTALL RADIATOR

  1. A112140
    Install the radiator with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Attach the 4 clamps of the 2 front airbag sensors from harnesses to the radiator.

  1. Connect the 2 front airbag sensor front connectors.


51. INSTALL RADIATOR SIDE DEFLECTOR RH

  1. A112159
    Install the deflector with the 2 clips and attach the claw.


52. INSTALL RADIATOR SIDE DEFLECTOR LH
  1. Install the deflector with the 2 clips and attach the claw.


53. INSTALL AIR CLEANER

Torque:
8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


54. INSTALL RADIATOR GRILLE
  1. Attach the 6 claws to install the radiator grille.

  1. Install the 2 screws and 2 clips.


55. CONNECT NO. 2 VENTILATION HOSE

56. INSTALL HOOD
  1. Install the hood with the 4 bolts and adjust the hood to the correct position.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Connect the washer nozzle hose.


57. INSTALL BATTERY

58. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


59. ADD ENGINE OIL
  1. Clean and install the oil drain plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Add fresh engine oil.

    Standard capacity:
    Item
    Capacity
    Drain and refill with oil filter change
    5.5 liters (5.8 US qts, 4.8 Imp. qts)
    Drain and refill without oil filter change
    5.2 liters (5.5 US qts, 4.6 Imp. qts)
    Dry fill
    6.6 liters (7.0 US qts, 5.8 Imp. qts)


    NOTICE:
    A308107
    Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

    If engine oil is on the location indicated by the arrow, replace the belt tensioner.

  1. Install the oil filler cap.


60. ADD ENGINE COOLANT
  1. Tighten all the plugs and fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plug

    Standard capacity:
    Item
    Specified Condition
    A/T
    9.8 liters (10.4 US qts, 8.6 Imp. qts)
    M/T
    8.5 liters (9.0 US qts, 7.5 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic and technology consists of a combination of low phosphates and organic acids).
    2. Please contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.

  1. Install the radiator cap.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

    2. Maintain the engine speed at 2,000 to 2,500 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A112081E01
    Check the coolant level in the radiator reservoir.
    If the coolant level is low, add SLLC to the reservoir F line.


61. CHECK FOR ENGINE COOLANT LEAKS

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A112135
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the cylinder block and head.


62. CHECK FOR FUEL LEAKS
  1. Connect the intelligent tester to the DLC3.

    1. Turn the ignition switch ON.

      NOTICE:
      Do not start the engine.

    2. Push the intelligent tester main switch ON.

    3. Select Active Test and enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check for fuel leaks.

    1. Check that there are no fuel leaks after performing maintenance anywhere on the fuel system.


63. CHECK FOR ENGINE OIL LEAKS
  1. Start the engine, and check that there are no oil leaks after performing maintenance.


64. INSTALL V-BANK COVER
  1. Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


65. INSPECT IGNITION TIMING

  1. A098433E01
    When using intelligent tester:
    Check the ignition timing.

    1. Connect the intelligent tester to the DLC3.

      HINT:
      Please refer to the intelligent tester operator's manual for further details.

      Ignition timing:
      7 to 24°BTDC @ idle
      (Transmission in neutral position)

    2. Disconnect the intelligent tester from the DLC3.

  1. A076315E01
    When not using intelligent tester.
    Check the ignition timing.

    1. Remove the air cleaner cap.

    2. Connect the tester probe of a timing light to the green-red read wire of the ignition coil connector for the No.1 cylinder.

    3. G039198E01
      Using SST, connect terminals TC and CG of the DLC3.
      SST
      09843-18040  

    4. A076316E01
      Using the timing light, check the ignition timing.

      Ignition timing:
      10 +- 2° BTDC @ idle
      (Transmission in neutral position)

    5. Remove the SST from the DLC3.

    6. Check the ignition timing.

      Ignition timing:
      7 to 24° BTDC @ idle
      (Transmission in neutral position)

    7. Disconnect the timing light from the engine.

    8. Install the air cleaner cap.


66. INSPECT ENGINE IDLE SPEED

  1. A098433E01
    When using intelligent tester:
    Check the idle speed.

    1. Connect the intelligent tester to the DLC3.

      HINT:
      Please refer to the intelligent tester operator's manual for further details.

    2. Switch the air conditioning OFF.

    3. Race the engine at 2,500 rpm for approximately 90 seconds.

    4. Check the idle speed.

      Idle speed:
      700 +- 50 rpm
      (Transmission in neutral position)

      If the idle speed is not as specified, check the air intake system

    5. Disconnect the intelligent tester from the DLC3.

  1. G039197E01
    When not using intelligent tester:
    Check the idle speed.

    1. Using SST, connect tachometer probe to terminal TAC of the DLC3.

      SST
      09843-18030  

    2. Switch the air conditioning OFF.

    3. Race the engine speed at 2,500 rpm for approximately 90 seconds.

    4. Check the idle speed.

      Idle speed:
      700 +- 50 rpm
      (Transmission in neutral position)

      If the idle speed is not as specified, check the air intake system.

    5. Disconnect the tachometer from the DLC3.


67. INSPECT CO/HC

HINT:
This check is for determining whether or not the idle CO/HC complies with regulations.

  1. Start the engine.

  1. Keep the engine speed at 2,500 rpm for approximately 180 seconds.

  1. G037188E01
    Insert CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe during idling.

  1. Immediately check CO/HC concentration at idle and/or 2,500 rpm.

    HINT:
    When performing the 2 mode (2,500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.
    If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.


    1. Check the A/F sensor operation and heated oxygen sensor operation.

    2. See the table below for possible causes, then inspect and correct the applicable causes if necessary.

      CO
      HC
      Symptom
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignitions:
      1. Incorrect timing
      2. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinder
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
      1. PCV hose
      2. Intake manifold
      3. Throttle body
      2. Lean mixture causing misfire.
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Faulty SFI system:
      1. Faulty pressure regulator
      2. Defective ECT sensor
      3. Faulty ECM
      4. Faulty injector
      5. Faulty throttle position sensor
      6. Faulty MAF sensor

← INSPECTION (from Jun 2011)INSTALLATION (Aug 2012 – Jul 2013) →