2014 Hilux · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Inspect the torque converter clutch assembly (Click here).


2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Install the torque converter clutch to the automatic transmission.

  1. C193529E01
    Using a vernier caliper and straightedge, measure dimension A between the surface of the engine that contacts the transmission*1, and the surface of the drive plate that contacts the converter*2. (#)

  1. C193531E01
    Using a vernier caliper and straightedge, measure dimension B shown in the illustration. Check that B is greater than A measured in step #.

    Standard:
    B = A + 1.00 mm (0.0394 in.) or more


3. INSTALL TRANSFER ASSEMBLY
  1. Install the transfer assembly (Click here).


4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

C193851E01
  1. Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter clutch centerpiece.

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent

    Maximum grease amount:
    Approximately 1.0 g (0.0353 oz)

  1. C196678E01
    Install the transmission to the engine with the 9 bolts.

    Torque:
    for bolt A:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    for bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    NOTICE:
    Confirm that the 2 knock pins are installed to the surface of the engine block before installing the transmission..

  1. C111234
    Hold the crankshaft pulley bolt with a wrench and install the 6 torque converter clutch setting bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    HINT:
    First install the black bolt, and then the other 5 bolts.


5. INSTALL FLYWHEEL HOUSING SIDE COVER
  1. Install the flywheel housing side cover to the cylinder block.


6. INSTALL STARTER ASSEMBLY
  1. for 1.4 kW Type:
    Install the starter assembly (Click here).

  1. for 1.6 kW Type:
    Install the starter assembly (Click here).


7. CONNECT WIRE HARNESS
  1. Connect the park/neutral position switch connector.

  1. Connect the transmission wire connector.

  1. Connect the 2 speed sensor connectors.

  1. Connect the No. 1 indicator switch connector.

  1. Connect the No. 2 indicator switch connector.

  1. Connect the No. 3 indicator switch connector.

  1. Connect the speed sensor connector.

  1. Attach the 7 wire harness clamps.

  1. Connect the ground cable with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


8. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

G034260E01
  1. Install the engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }


9. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

G034256E03
  1. Install the frame crossmember to the rear No. 1 engine mounting insulator with the 4 set bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Connect the ends of the frame crossmember to the vehicle with the 4 bolts and 4 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }


10. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C111232
  1. Install the control cable bracket with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }


11. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

C111231
  1. Connect the control cable with a new clip.

  1. Connect the control cable with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }


12. INSTALL OIL COOLER TUBE

C111230
  1. Loosely install the tip of the inlet oil cooler tube to the automatic transmission by hand.

  1. Loosely install the tip of the outlet oil cooler tube to the automatic transmission by hand.

  1. Install the 2 clamps with the 2 bolts.

    Torque:
    5.0 N*m{ 50 kgf*cm , 43 in.*lbf }

  1. C244749E01
    Using a union nut wrench, tighten the inlet and outlet oil cooler tubes.

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


13. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

  1. A076440E02
    Set a new gasket to the RH cylinder head with the oval shape facing forward.

    NOTICE:
    Be careful of the installation direction.

  1. Install the exhaust manifold with the 6 nuts. Uniformly tighten the nuts in several passes.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the A/F sensor connector.


14. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

  1. A076439E01
    Set a new gasket to the LH cylinder head with the oval shape facing backward.

    NOTICE:
    Be careful of the installation direction.

  1. Install the exhaust manifold with the 6 nuts. Uniformly tighten the nuts in several passes.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the A/F sensor connector.


15. INSTALL NO. 2 MANIFOLD STAY

F050356E01
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


16. INSTALL MANIFOLD STAY

F050360E01
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


17. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
  1. for TSAM Made:
    Install the propeller shaft with center bearing assembly (Click here).

  1. for TMT Made:
    Install the propeller shaft with center bearing assembly (Click here).


18. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
  1. for TSAM Made:
    Install the front propeller shaft assembly (Click here).

  1. for TMT Made:
    Install the front propeller shaft assembly (Click here).


19. INSTALL EXHAUST PIPE
  1. Install the exhaust pipe (Click here).


20. CONNECT HEATED OXYGEN SENSOR
  1. Connect the 2 sensor connectors.


21. INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY

  1. C213733E02
    While pushing the select return spring to the left with the end of the transfer high and low shift lever, insert the end of the shift lever into the shift fork.

  1. C213734E03
    While holding down the shift lever cap, install the snap ring to install the transfer high and low shift lever.

  1. Return the transfer front drive shift boot to its original position.


22. INSTALL SHIFT LEVER BOOT ASSEMBLY
  1. Install the shift lever boot with the 4 screws.


23. INSTALL CONSOLE BOX ASSEMBLY

B278048E01
  1. Install the console box with the 4 screws and 2 bolts.

  1. Install the 2 clips.

    Text in Illustration 
    *1
    Screw
    *2
    Bolt
    *3
    Clip


24. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. Attach the 12 claws to install the upper console panel.

    B277548E01

    Text in Illustration 
    *A
    for 2WD
    *B
    for 4WD


25. INSTALL PARKING BRAKE HOLE COVER SUB-ASSEMBLY
  1. Attach the 4 claws to install the parking brake hole cover.


26. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

B277222
  1. Install the shift lever knob and twist it in the direction indicated by the arrow.


27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Certain systems need to be initialized after disconnecting and reconnecting the cable to the negative (-) battery terminal.


28. ADD AUTOMATIC TRANSMISSION FLUID
  1. Add automatic transmission fluid (Click here).


29. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D, and moves in reverse after shifting to R.
    If the results are not as specified, inspect the park/ neutral position switch and check the shift lever.


30. PERFORM INITIALIZATION
  1. Perform initialization (Click here).


31. CHECK FOR EXHAUST GAS LEAKS

32. INSTALL NO. 3 ENGINE UNDER COVER

Torque:
28 N*m{ 285 kgf*cm , 21 ft.*lbf }


33. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 285 kgf*cm , 21 ft.*lbf }


34. INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m{ 285 kgf*cm , 21 ft.*lbf }

← REMOVAL (from Aug 2013)INSTALLATION (Aug 2012 – Jul 2013) →