B1615/14 Front Airbag Sensor LH Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2013 from Aug 2013
SYSTEM DESCRIPTION
The front airbag sensor LH consists of the diagnostic circuit and front deceleration sensor. The center airbag sensor receives signals from the front deceleration sensor, and determines whether or not the SRS should be activated. DTC B1615/14 is recorded when a malfunction is detected in the front airbag sensor LH circuit.| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1615/14 |
When one of following conditions is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
![]() ![]() |
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1615/14 is not output.
- HINT:
- DTCs other than DTC B1615/14 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch OFF.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and front airbag sensor LH.
- OK:
- Connectors are connected.
|
|
||||
| OK | |
| 3. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN) |
![]() ![]() |
Disconnect the connectors from the center airbag sensor and front airbag sensor LH.
Using a service wire, connect terminals A14-28 (-SL) and A14-30 (+SL) of connector B.
- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
A5-2 (+SL) - A5-1 (-SL)
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT) |
![]() ![]() |
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
A5-2 (+SL) - A5-1 (-SL)
1 MΩ or higher
|
|
||||
| OK | |
| 5. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO B+) |
![]() ![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
A5-2 (+SL) - Body ground
Below 1 V
A5-1 (-SL) - Body ground
Below 1 V
|
|
||||
| OK | |
| 6. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO GROUND) |
![]() ![]() |
Turn the ignition switch OFF.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
A5-2 (+SL) - Body ground
1 MΩ or higher
A5-1 (-SL) - Body ground
1 MΩ or higher
|
|
||||
| OK | |
| 7. CHECK FRONT AIRBAG SENSOR LH |
![]() ![]() |
Connect the connectors to the center airbag sensor.
Interchange the front airbag sensor LH with the front airbag sensor RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result
Proceed to
DTC B1615/14 is output
A
DTC B1610/13 is output
B
DTC B1610/13 and B1615/14 are not output
C
|
|
||||
|
|
||||
| C | ||
| ||
| 8. CHECK ENGINE ROOM MAIN WIRE (OPEN) |
![]() ![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Using a service wire, connect terminals A5-1 (-SL) and A5-2 (+SL) of connector B.
- NOTICE:
- Do not forcibly insert a service wire into the terminals of the connector.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
IF1-3 (+SL) - IF1-4 (-SL)
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 9. CHECK ENGINE ROOM MAIN WIRE (SHORT) |
![]() ![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
IF1-3 (+SL) - IF1-4 (-SL)
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 10. CHECK ENGINE ROOM MAIN WIRE (TO B+) |
![]() ![]() |
Turn the ignition switch OFF.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the engine room main wire connector from the instrument panel wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
IF1-3 (+SL) - Body ground
Below 1 V
IF1-4 (-SL) - Body ground
Below 1 V
|
|
||||
| OK | ||
| ||
| 11. CHECK ENGINE ROOM MAIN WIRE (TO GROUND) |
![]() ![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
IF1-3 (+SL) - Body ground
1 MΩ or higher
IF1-4 (-SL) - Body ground
1 MΩ or higher
|
|
||||
| OK | ||
| ||






