2014 Hilux · Service Manual RESTRAINTS

B1620/21 Driver Side - Side Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013

DESCRIPTION

The side airbag sensor (driver side) consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc..
If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1620/21 is recorded when a malfunction is detected in the side airbag sensor (driver side) circuit.
DTC Code
Detection Condition
Trouble Area
B1620/21
One of the following conditions is met:
  1. A side airbag sensor (driver side) malfunction
  2. A center airbag sensor malfunction
  1. Side airbag sensor (driver side)
  2. Rear airbag sensor (driver side)
  3. Floor wire
  4. Center airbag sensor assembly

WIRING DIAGRAM

C194828E09
C199306E12

INSPECTION PROCEDURE


1. CHECK VEHICLE CONDITION
  1. Check vehicle condition.

    Result 
    Result
    Proceed to
    for LHD
    A
    for RHD
    B



A
Go to step 11
B


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and side airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3. CHECK CONNECTORS

  1. C215710E02
    Disconnect the connectors from the center airbag sensor and side airbag sensor RH.

  1. Check that the connectors (on the center airbag sensor side and side airbag sensor RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

Text in illustration 
*1
Side Airbag Sensor RH
*2
Center Airbag Sensor Assembly
*3
Floor Wire


NG
REPLACE FLOOR WIRE
OK


4. CHECK SIDE AIRBAG SENSOR RH CIRCUIT

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C241326E01

    Text in illustration 
    *A
    for Extra Cab, Double Cab
    *B
    for Single Cab
    *1
    Side Airbag Sensor RH
    *2
    Center Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Connector C
    *5
    Connector B
    *6
    Service Wire
    *a
    Rear view of wire harness connector:
    (to Side Airbag Sensor RH)
    *b
    Rear view of wire harness connector:
    (to Center Airbag Sensor Assembly)

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (for Extra Cab, Double Cab):
    Tester Connection
    Switch Condition
    Specified Condition
    F24-3 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V
    F24-4 (BBR+) - Body ground

    Standard Voltage (for Single Cab):
    Tester Connection
    Switch Condition
    Specified Condition
    F37-1 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V
    F37-2 (BBR+) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for Extra Cab, Double Cab):
    Tester Connection
    Condition
    Specified Condition
    F24-3 (BBR-) - F24-4 (BBR+)
    Always
    Below 1 Ω

    Standard Resistance (for Single Cab):
    Tester Connection
    Condition
    Specified Condition
    F37-1 (BBR-) - F37-2 (BBR+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for Extra Cab, Double Cab):
    Tester Connection
    Condition
    Specified Condition
    F24-3 (BBR-) - F24-4 (BBR+)
    Always
    1 MΩ or higher
    F24-3 (BBR-) - Body ground
    F24-4 (BBR+) - Body ground

    Standard Resistance (for Single Cab):
    Tester Connection
    Condition
    Specified Condition
    F37-1 (BBR-) - F37-2 (BBR+)
    Always
    1 MΩ or higher
    F37-1 (BBR-) - Body ground
    F37-2 (BBR+) - Body ground



NG
REPLACE FLOOR WIRE
OK


5. CHECK SIDE AIRBAG SENSOR RH

  1. C198515E04
    Connect the connector to the center airbag sensor.

  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1620/21 and B1625/22 are not output
    A
    DTC B1625/22 is output
    B
    DTC B1620/21 is output (for Single Cab)
    C
    DTC B1620/21 is output (for Extra Cab, Double Cab)
    D
    Text in illustration 
    *1
    Side Airbag Sensor LH
    *2
    Center Airbag Sensor Assembly

    HINT:
    Codes other than DTC B1620/21 and B1625/22 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE SIDE AIRBAG SENSOR RH

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
D


6. CHECK CONNECTION OF CONNECTORS
  1. Check that the connector is properly connected to the rear airbag sensor RH.

    OK:
    The connector is properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


7. CHECK CONNECTORS

  1. C206430E03
    Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

  1. Check that the connector (on the rear airbag sensor RH side) is not damaged.

    OK:
    The connector is not deformed or damaged.

    Text in illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Floor Wire
    *3
    Side Airbag Sensor RH



NG
REPLACE FLOOR WIRE
OK


8. CHECK REAR AIRBAG SENSOR RH CIRCUIT

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C241327E01

    Text in illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side Airbag Sensor RH
    *3
    Connector C
    *4
    Connector B
    *5
    Service Wire
    *6
    Floor Wire
    *a
    Rear view of wire harness connector:
    (to Rear Airbag Sensor RH)
    *b
    Rear view of wire harness connector:
    (to Side Airbag Sensor RH)

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R13-2 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    R13-1 (BCR-) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R13-2 (BCR+) - R13-1 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R13-2 (BCR+) - R13-1 (BCR-)
    Always
    1 MΩ or higher
    R13-2 (BCR+) - Body ground
    R13-1 (BCR-) - Body ground



NG
REPLACE FLOOR WIRE
OK


9. CHECK DTC

  1. C241328E01
    Connect the connectors to the side airbag sensor RH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1620/21 is output.

    Text in illustration 
    *1
    Rear Airbag Sensor RH
    *2
    Side Airbag Sensor RH

    HINT:
    Codes other than B1620/21 may be output at this time, but they are not related to this check.

  1. Connect the connectors to the rear airbag sensor RH.



NG
REPLACE REAR AIRBAG SENSOR RH
OK


10. CHECK SIDE AIRBAG SENSOR RH

  1. C198515E04
    Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1620/21 and B1625/22 are not output
    A
    DTC B1625/22 is output
    B
    DTC B1620/21 is output
    C
    Text in illustration 
    *1
    Side Airbag Sensor LH
    *2
    Center Airbag Sensor Assembly

    HINT:
    Codes other than DTC B1620/21 and B1625/22 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE SIDE AIRBAG SENSOR RH
C

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

11. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and side airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


12. CHECK CONNECTORS

  1. C215710E02
    Disconnect the connectors from the center airbag sensor and side airbag sensor LH.

  1. Check that the connectors (on the center airbag sensor side and side airbag sensor LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Text in illustration 
    *1
    Side Airbag Sensor LH
    *2
    Center Airbag Sensor Assembly
    *3
    Floor Wire



NG
REPLACE FLOOR WIRE
OK


13. CHECK SIDE AIRBAG SENSOR LH CIRCUIT

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C214253E09

    Text in illustration 
    *1
    Side Airbag Sensor LH
    *2
    Center Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Connector C
    *5
    Connector B
    *6
    Service Wire
    *a
    Rear view of wire harness connector:
    (to Side Airbag Sensor LH)
    *b
    Rear view of wire harness connector:
    (to Center Airbag Sensor Assembly)

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F25-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V
    F25-4 (BBL+) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F25-3 (BBL-) - F25-4 (BBL+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F25-3 (BBL-) - F25-4 (BBL+)
    Always
    1 MΩ or higher
    F25-3 (BBL-) - Body ground
    F25-4 (BBL+) - Body ground



NG
REPLACE FLOOR WIRE
OK


14. CHECK SIDE AIRBAG SENSOR LH

  1. C198515E05
    Connect the connector to the center airbag sensor.

  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1620/21 and B1625/22 are not output
    A
    DTC B1625/22 is output
    B
    DTC B1620/21 is output
    C
    Text in illustration 
    *1
    Side Airbag Sensor RH
    *2
    Center Airbag Sensor Assembly

    HINT:
    Codes other than DTC B1620/21 and B1625/22 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE SIDE AIRBAG SENSOR LH
C


15. CHECK CONNECTION OF CONNECTORS
  1. Check that the connector are properly connected to the rear airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


16. CHECK CONNECTORS

  1. C206430E03
    Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.

  1. Check that the connector (on the rear airbag sensor LH side) is not damaged.

    OK:
    The connectors are not deformed or damaged.

    Text in illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Floor Wire
    *3
    Side Airbag Sensor LH



NG
REPLACE FLOOR WIRE
OK


17. CHECK REAR AIRBAG SENSOR LH CIRCUIT

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C241327E02

    Text in illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side Airbag Sensor LH
    *3
    Connector C
    *4
    Connector B
    *5
    Service Wire
    *6
    Floor Wire
    *a
    Rear view of wire harness connector:
    (to Rear Airbag Sensor LH)
    *b
    Rear view of wire harness connector:
    (to Side Airbag Sensor LH)

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R14-2 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    R14-1 (BCL-) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCL-) and 1 (BCL+) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R14-2 (BCL+) - R14-1 (BCL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R14-2 (BCL+) - R14-1 (BCL-)
    Always
    1 MΩ or higher
    R14-2 (BCL+) - Body ground
    R14-1 (BCL-) - Body ground



NG
REPLACE FLOOR WIRE
OK


18. CHECK DTC

  1. C241328E01
    Connect the connectors to the side airbag sensor LH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1620/21 is output.

    Text in illustration 
    *1
    Rear Airbag Sensor LH
    *2
    Side Airbag Sensor LH

HINT:
Codes other than B1620/21 may be output at this time, but they are not related to this check.

  1. Connect the connectors to the rear airbag sensor LH.



NG
REPLACE REAR AIRBAG SENSOR LH
OK


19. CHECK SIDE AIRBAG SENSOR LH

  1. C198515E05
    Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1620/21 and B1625/22 are not output
    A
    DTC B1625/22 is output
    B
    DTC B1620/21 is output
    C
    Text in illustration 
    *1
    Side Airbag Sensor RH
    *2
    Center Airbag Sensor Assembly

    HINT:
    Codes other than DTC B1620/21 and B1625/22 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE SIDE AIRBAG SENSOR LH
C

REPLACE CENTER AIRBAG SENSOR ASSEMBLY


← B1615/14 Front Airbag Sensor LH Circuit Malfunction (from Aug 2013)B1620/21 Driver Side - Side Airbag Sensor Circuit Malfunction (from Aug 2013) →