TERMINALS OF ECU
System information · Vehicles built from Jun 2011
| CHECK TRANSPONDER KEY AMPLIFIER |
![]() ![]() |
Measure the resistance and voltage according to the value(s) in the table below.
Inspection with Ignition Switch Off Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
T20-7 (AGND) - Body ground
-
L-O - Body ground
Ground
Always
Below 1 Ω
-
T20-1 (VC5) - T20-7 (AGND)
Input
L - L-O
Transponder key amplifier power supply
No key in ignition key cylinder
Below 1 V
-
T20-4 (CODE) - T20-7 (AGND)
Output
L-Y - L-O
Demodulated signal of key code data
No key in ignition key cylinder
Below 1 V
-
T20-5 (TXCT) - T20-7 (AGND)
Input
L-B - L-O
Key code output signal
No key in ignition key cylinder
Below 1 V
-
- If the result is not as specified, there may be a malfunction on the wire harness side.
Inspection of Waveforms of Communication Signals between Transponder Key Amplifier and Transponder Key ECU Assembly Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
T20-1 (VC5) - T20-7 (AGND)
Input
L - L-O
Transponder key amplifier power supply
No key in ignition key cylinder
Below 1 V
- BCC Malfunction
- Abnormal Status
- Different Encrypt Code
- Different Serial Number
Key inserted in ignition key cylinder
4.6 to 5.4 V
T20-4 (CODE) - T20-7 (AGND)
Output
L-Y - L-O
Demodulated signal of key code data
No key in ignition key cylinder
Below 1 V
Key inserted in ignition key cylinder
Pulse generation (See waveform 1)
T20-5 (TXCT) - T20-7 (AGND)
Input
L-B - L-O
Key code output signal
No key in ignition key cylinder
Below 1 V
Key inserted in ignition key cylinder
Pulse generation (See waveform 2)
- If the result is not as specified, the amplifier may have a malfunction.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Inspect using an oscilloscope.

- HINT:
- The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)
Measurement Condition Item
Content
Tester Connection
T20-4 (CODE) - T20-7 (AGND)
Tool Setting
5 V/DIV., 20 ms./DIV.
Condition
Key inserted in ignition key cylinder
Waveform 2 (Reference)

Measurement Condition Item
Content
Tester Connection
T20-5 (TXCT) - T20-7 (AGND)
Tool Setting
5 V/DIV., 20 ms./DIV.
Condition
Key inserted in ignition key cylinder
| CHECK TRANSPONDER KEY ECU ASSEMBLY |
![]() ![]() |
Disconnect the T21 transponder key ECU assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
T21-16 (GND) - Body ground
-
G - Body ground
Ground
Always
Below 1 Ω
-
T21-1 (+B) - T21-16 (GND)
Input
L-Y - G
Battery
Always
11 to 14 V
+B
T21-2 (IG) - T21-16 (GND)
Input
B-O - G
Ignition switch
Ignition switch off
Below 1 V
IG SW
Ignition switch ON
11 to 14 V
T21-3 (KSW) - T21-16 (GND)
Input
BR - G
Unlock warning switch
No key in ignition key cylinder
10 kΩ or higher
Key SW/B2780
Key inserted in ignition key cylinder
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the T21 transponder key ECU assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
T21-14 (VC5) - T21-16 (GND)
Input
L - G
Transponder key amplifier power supply
No key in ignition key cylinder
Below 1 V
- BCC Malfunction
- Abnormal Status
- Different Encrypt Code
- Different Serial Number
Key inserted in ignition key cylinder
4.6 to 5.4 V
T21-4 (TXCT) - T21-16 (GND)
Input
L-B - G
Key code output signal
No key in ignition key cylinder
Below 1 V
Key inserted in ignition key cylinder
Pulse generation (See waveform 1)
T21-15 (CODE) - T21-16 (GND)
Output
L-Y - G
Demodulated signal of key code data
No key in ignition key cylinder
Below 1 V
Key inserted in ignition key cylinder
Pulse generation (See waveform 2)
T21-7 (CTY) - T21-16 (GND)
Input
R-B - G
Front door courtesy light switch (for Driver Side)
Driver door closed
10 kΩ or higher
D Door Courtesy SW
Driver door open
Below 1 Ω
T21-13 (EFIO) - T21-16 (GND)
Input
Y-G - G
ECM output signal
Ignition switch off
Below 1 V
E/G Start Permission
Ignition switch ON
Pulse generation (See waveform 3)
T21-12 (EFII) - T21-16 (GND)
Output
Y-B - G
ECM input signal
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
Pulse generation (See waveform 4)
E/G Start Permission
T21-8 (IND) - T21-16 (GND)
Output
G-R - G
Security indicator light signal
Immobiliser set
Alternating between 11 to 14 V and below 1 V
-
Immobiliser unset
Below 1 V
T21-9 (D) - T21-16 (GND)
Input/Output
B - G
Diagnosis tester communication
Always
Pulse generation
-
T21-5 (AGND) - Body ground
-
L-O - Body ground
Transponder key amplifier ground
Always
Below 1 Ω
-
- If the result is not as specified, the ECU may have a malfunction.
- BCC Malfunction
Inspect using an oscilloscope.

- HINT:
- The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)
Measurement Condition Item
Content
Tester Connection
T21-4 (TXCT) - T21-16 (GND)
Tool Setting
5 V/DIV., 20 ms./DIV.
Condition
Key inserted in ignition key cylinder
Waveform 2 (Reference)

Measurement Condition Item
Content
Tester Connection
T21-15 (CODE) - T21-16 (GND)
Tool Setting
5 V/DIV., 20 ms./DIV.
Condition
Key inserted in ignition key cylinder
Waveform 3 (Reference)

Measurement Condition Item
Content
Tester Connection
T21-13 (EFIO) - T21-16 (GND)
Tool Setting
10 V/DIV., 100 ms./DIV.
Condition
Ignition switch ON
Waveform 4 (Reference)

Measurement Condition Item
Content
Tester Connection
T21-12 (EFII) - T21-16 (GND)
Tool Setting
5 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
| CHECK ECM (for 1TR-FE, 2TR-FE) |


Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E10-15 (IMO) - Body ground
Y-B - Body ground
Transponder key ECU assembly output signal
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
Pulse generation (See waveform 1)
E10-16 (IMI) - Body ground
Y-G -Body ground
Transponder key ECU assembly input signal
Ignition switch off
Below 1 V
Ignition switch ON
Pulse generation (See waveform 2)
- If the result is not as specified, the ECM may have a malfunction.
- If the result is not as specified, the ECM may have a malfunction.
Inspect using an oscilloscope.
- HINT:
- The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)

Measurement Condition Item
Content
Tester Connection
E10-15 (IMO) - Body ground
Tool Setting
5 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
Waveform 2 (Reference)

Measurement Condition Item
Content
Tester Connection
E10-16 (IMI) - Body ground
Tool Setting
10 V/DIV., 100 ms./DIV.
Condition
Ignition switch ON
| CHECK ECM (for 1GR-FE) |


Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E13-15 (IMO) - Body ground
Y-B - Body ground
Transponder key ECU assembly output signal
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
Pulse generation (See waveform 1)
E13-16 (IMI) - Body ground
Y-G -Body ground
Transponder key ECU assembly input signal
Ignition switch off
Below 1 V
Ignition switch ON
Pulse generation (See waveform 2)
- If the result is not as specified, the ECM may have a malfunction.
- If the result is not as specified, the ECM may have a malfunction.
Inspect using an oscilloscope.
- HINT:
- The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)

Measurement Condition Item
Content
Tester Connection
E13-15 (IMO) - Body ground
Tool Setting
5 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
Waveform 2 (Reference)

Measurement Condition Item
Content
Tester Connection
E13-16 (IMI) - Body ground
Tool Setting
10 V/DIV., 100 ms./DIV.
Condition
Ignition switch ON
| CHECK ECM (for 1KD-FTV, 2KD-FTV) (except DPF) |


Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E6-29 (IMO) - Body ground
Y-B - Body ground
Transponder key ECU assembly output signal
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
Pulse generation (See waveform 1)
E6-30 (IMI) - Body ground
Y-G -Body ground
Transponder key ECU assembly input signal
Ignition switch off
Below 1 V
Ignition switch ON
Pulse generation (See waveform 2)
- If the result is not as specified, the ECM may have a malfunction.
- If the result is not as specified, the ECM may have a malfunction.
Inspect using an oscilloscope.
- HINT:
- The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)

Measurement Condition Item
Content
Tester Connection
E6-29 (IMO) - Body ground
Tool Setting
5 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
Waveform 2 (Reference)

Measurement Condition Item
Content
Tester Connection
E6-30 (IMI) - Body ground
Tool Setting
10 V/DIV., 100 ms./DIV.
Condition
Ignition switch ON
| CHECK ECM (for 1KD-FTV, 2KD-FTV) (for DPF) |


Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E30-29 (IMO) - Body ground
Y-B - Body ground
Transponder key ECU assembly output signal
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
Pulse generation (See waveform 1)
E30-28 (IMI) - Body ground
Y-G -Body ground
Transponder key ECU assembly input signal
Ignition switch off
Below 1 V
Ignition switch ON
Pulse generation (See waveform 2)
- If the result is not as specified, the ECM may have a malfunction.
- If the result is not as specified, the ECM may have a malfunction.
Inspect using an oscilloscope.
- HINT:
- The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)

Measurement Condition Item
Content
Tester Connection
E30-29 (IMO) - Body ground
Tool Setting
5 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
Waveform 2 (Reference)

Measurement Condition Item
Content
Tester Connection
E30-28 (IMI) - Body ground
Tool Setting
10 V/DIV., 100 ms./DIV.
Condition
Ignition switch ON

