2014 Hilux · Service Manual SECURITIES

B2797 Communication Malfunction No. 1

Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

This DTC is stored when a communication error occurs between the transponder key amplifier and transponder key ECU assembly. Some possible reasons for the communication error are: 1) 2 or more ignition keys are positioned too close together, or 2) noise is occurring in the communication line.
DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2797
A key with a BCC malfunction is inserted into the ignition key cylinder (1 trip detection logic*).
  1. Key
  2. Harness or connector
  3. Transponder key amplifier
  4. Transponder key ECU assembly
Insert the key into the ignition key cylinder
  1. *: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started.
-
Related Data List and Active Test 
DTC Code
Data List and Active Test
B2797
BCC Malfunction

WIRING DIAGRAM

B278721E02

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the transponder key ECU assembly, refer to the Service Bulletin.
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


1. CHECK KEY

  1. B276087
    Check whether the ignition key being used is near other ignition keys, as shown in the illustration. Also, check whether a key ring is in contact with the key grip.
    Result 
    Result
    Proceed to
    Key is near other keys and/or key ring is in contact with key grip
    A
    Key is not near other keys and/or key ring is not in contact with key grip
    B



B
Go to step 3
A


2. CHECK FOR DTC
  1. Separate the keys from each other and/or remove the key ring.

  1. Clear the DTC (Click here).

  1. Insert a key into the ignition key cylinder, and then remove it. Repeat this for all the other keys.

  1. Check that no code is output.

    OK:
    DTC B2797 is not output.



NG
Go to step 3
OK

END

3. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)
  1. Disconnect the T21 transponder key ECU assembly connector.

  1. Disconnect the T20 transponder key amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T21-15 (CODE) - T20-4 (CODE)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK TRANSPONDER KEY ECU ASSEMBLY

  1. Using an oscilloscope or the intelligent tester, check for noise in the waveform between the terminals of the T20 transponder key amplifier connector and T21 transponder key ECU assembly connector.B274401E04

    Text in Illustration 
    *a
    Component with harness connected
    (Transponder Key Amplifier)
    *b
    Component with harness connected
    (Transponder Key ECU Assembly)
    *c
    Noise should not appear
    -
    -
    Measurement Condition 
    Item
    Content
    Tester Connection
    T21-15 (CODE) - T20-4 (CODE)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    Key inserted in ignition key cylinder

    OK:
    No noise is present (see illustration).



NG
FIND CAUSE OF NOISE AND REMOVE IT
OK


5. REPLACE TRANSPONDER KEY AMPLIFIER (OPERATION)
  1. Temporally replace the transponder key amplifier with a new or normally functioning one (Click here).


NEXT


6. CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts normally.

    OK:
    Engine starts.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

END (TRANSPONDER KEY AMPLIFIER IS DEFECTIVE)


← B2797 Communication Malfunction No. 1 (Jun 2011 – Jul 2012)B2797 Communication Malfunction No. 1 (from Aug 2013) →