2014 Hilux · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from Nov 2011

Versions by build date: Jun 2011 – Oct 2011 from Nov 2011


CHECK THEFT WARNING ECU ASSEMBLY (except 2 Step Unlock Function)
B119764E11
  1. Disconnect the T36 theft warning ECU assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T36-1 (E) - Body ground
    B-W - Body ground
    Ground
    Always
    Below 1 Ω
    T36-4 (+B1) -T36-1 (E)
    L-Y - B-W
    Battery power supply
    Always
    11 to 14 V
    T36-14 (+B2) - T36-1 (E)
    G - B-W
    Battery power supply
    Always
    11 to 14 V
    T36-18 (IG) - T36-1 (E)
    R-L - B-W
    Ignition power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T36 theft warning ECU assembly connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T36-3 (DMLP) - Body ground*
    P - Body ground
    Interior lights output signal
    Interior lights on
    Below 1 V
    Interior lights off
    11 to 14 V
    T36-5 (KSW) - Body ground
    G-Y - Body ground
    Unlock warning switch input signal
    No key in ignition key cylinder
    10 kΩ or higher
    Key inserted in ignition key cylinder
    Below 1 Ω
    T36-7 (CTY) - Body ground
    R-L - Body ground
    All door courtesy switches input signal
    One or more doors are open
    Below 1 V
    All doors are closed
    11 to 14 V
    T36-13 (SH-) - Body ground
    B - Body ground
    Security horn output signal
    Security horn assembly off
    Below 1 V
    Security horn assembly on
    Pulse generation
    T36-25 (L2) - Body ground
    L - Body ground
    Door lock output signal
    Ignition switch off, all doors closed and transmitter switch not pressed
    Below 1 V
    Ignition switch off, all doors closed and transmitter lock switch pressed
    Pulse generation
    T36-26 (UL3) -Body ground
    L-W - Body ground
    Door unlock output signal
    Ignition switch off, all doors closed and transmitter switch not pressed
    Below 1 V
    Ignition switch off, all doors closed and transmitter unlock switch pressed
    Pulse generation
    T36-28 (HAZD) - Body ground
    G-O -Body ground
    All hazard warning light output signals
    Hazard warning signal switch assembly off
    11 to 14 V
    Hazard warning signal switch assembly on
    Below 1 V
    1. *: w/ Illuminated Entry Function
    2. If the result is not as specified, the theft warning ECU assembly may have a malfunction.


CHECK THEFT WARNING ECU ASSEMBLY (for 2 Step Unlock Function)
B119765E03
  1. Disconnect the T39 theft warning ECU assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T39-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    T39-3 (+B1) -T39-1 (E)
    L-Y - W-B
    Battery power supply
    Always
    11 to 14 V
    T39-4 (IG) - T39-1 (E)
    R-L - W-B
    Ignition power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    T39-12 (+B2) - T39-1 (E)
    LG - W-B
    Battery power supply
    Always
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T39 theft warning ECU assembly connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T39-2 (DMLP) - Body ground*
    P - Body ground
    Interior lights output signal
    Interior lights on
    Below 1 V
    Interior lights off
    11 to 14 V
    T39-5 (KSW) - Body ground
    G-Y - Body ground
    Unlock warning switch input signal
    No key in ignition key cylinder
    10 kΩ or higher
    Key inserted in ignition key cylinder
    Below 1 Ω
    T39-7 (CTY) - Body ground
    R-L - Body ground
    All door courtesy switches input signal
    One or more doors are open
    Below 1 V
    All doors are closed
    11 to 14 V
    T39-20 (L2) - Body ground
    L - Body ground
    Door lock output signal
    Ignition switch off, all doors closed and transmitter switch not pressed
    Below 1 V
    Ignition switch off, all doors closed and transmitter lock switch pressed
    Pulse generation
    T39-21 (UL3) -Body ground
    L-W - Body ground
    Door unlock output signal
    Ignition switch off, all doors closed and transmitter switch not pressed
    Below 1 V
    Ignition switch off, all doors closed and transmitter unlock switch pressed
    Pulse generation
    T39-23 (HAZD) - Body ground
    G-O -Body ground
    All hazard warning light output signals
    Hazard warning signal switch assembly off
    11 to 14 V
    Hazard warning signal switch assembly on
    Below 1 V
    T39-26 (SH-) - Body ground
    B - Body ground
    Security horn output signal
    Security horn assembly off
    Below 1 V
    Security horn assembly on
    Pulse generation
    1. *: w/ Illuminated Entry Function
    2. If the result is not as specified, the theft warning ECU assembly may have a malfunction.


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY (INTEGRATION RELAY)
B276157E01
Text in Illustration 
*1
Integration Relay
-
-
  1. Disconnect the 2A, 2D, 2H and 2L driver side junction block assembly connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2D-9 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    2D-18 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    2H-4 (ALTB) - Body ground
    LG - Body ground
    Battery power supply
    Always
    11 to 14 V
    2L-12 (BECU) - 2D-9 (GND)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    2A-6 (SIG) - Body ground
    B-Y - Body ground
    Ignition switch
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the 2A, 2D, 2H and 2L driver side junction block assembly connectors.

  4. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2A-4 (L1) - Body ground
    L - Body ground
    1. Power window regulator master switch assembly (door control switch) lock input signal
    2. Driver side door key-linked lock input signal
    1. Power window regulator master switch assembly (door control switch) locked
    2. Driver side door key cylinder in lock position
    Below 1 V
    1. Power window regulator master switch assembly (door control switch) off
    2. Ignition switch off, all doors closed and driver side door key cylinder in neutral position
    11 to 14 V
    2D-4 (UL1) - Body ground
    L-W - Body ground
    1. Power window regulator master switch assembly (door control switch) unlock input signal
    2. Driver side door key-linked unlock input signal
    1. Power window regulator master switch assembly (door control switch) unlocked
    2. Driver side door key cylinder in unlock position
    Below 1 V
    1. Power window regulator master switch assembly (door control switch) off
    2. Ignition switch off, all doors closed and driver side door key cylinder in neutral position
    11 to 14 V
    2E-3 (PCTY) - Body ground
    P - Body ground
    All courtesy light switches input signal
    One or more doors open
    Below 1 V
    All doors closed
    11 to 14 V
    2N-12 (ILE) - Body ground*1
    P - Body ground
    Ignition key cylinder light output signal
    Ignition key cylinder light on
    Below 1 V
    Ignition key cylinder light off
    11 to 14 V
    2K-10 (ACT-) - Body ground
    L-Y - Body ground
    Door lock motor unlock drive output signal (passenger door and rear RH door*2, *4 or rear LH door*3, *4)
    Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position
    Below 1 V
    Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in unlock position
    11 to 14 V
    2K-11 (ACT+) - Body ground
    L - Body ground
    Door lock motor lock drive output signal (passenger door and rear RH door*2, *4 or rear LH door*3, *4)
    Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position
    Below 1 V
    Power window regulator master switch assembly (door control switch) or driver side door key cylinder in lock position
    11 to 14 V
    2O-10 (KSW) - Body ground
    G-Y - Body ground
    Unlock warning switch input signal
    No key in ignition key cylinder
    10 kΩ or higher
    Key inserted in ignition key cylinder
    Below 1 Ω
    2O-27 (DCTY) - Body ground
    R-B - Body ground
    Front door courtesy light switch assembly LH*2 or RH*3 input signal
    Driver side door open
    Below 1 V
    Driver side door closed
    11 to 14 V
    2R-27 (ACT-) - Body ground
    L-Y - Body ground
    Door lock motor unlock drive output signal (driver door, and rear LH door*2, *4 or rear RH door*3, *4)
    Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position
    Below 1 V
    Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in unlock position
    11 to 14 V
    2R-28 (ACT+) - Body ground
    L - Body ground
    Door lock motor LOCK drive output signal (driver door, and rear LH door*2, *4 or rear RH door*3, *4)
    Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position
    Below 1 V
    Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in unlock position
    11 to 14 V
    1. *1: w/ Illuminated Entry Function
    2. *2: for LHD
    3. *3: for RHD
    4. *4: for Double Cab
    5. If the result is not as specified, the driver side junction block assembly may have a malfunction.

← TERMINALS OF ECU (Jun 2011 – Oct 2011)Only Wireless Control Function is Inoperative (Jun 2011 – Jul 2013) →