2014 Hilux · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)
(Click here)

2. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)
(Click here)

3. REMOVE FRONT SEAT CUSHION COVER LH
  1. Remove the front seat cushion cover LH.


4. REMOVE FRONT SEAT INNER CUSHION SHIELD LH

B278169E01
  1. Remove the 2 screws.

  1. Detach the 2 hooks in the order shown in the illustration and remove the front seat inner cushion shield LH.


5. REMOVE VERTICAL SEAT ADJUSTER KNOB RH (for RHD, w/ Vertical Adjuster)

  1. B276710E01
    Using a screwdriver, remove the snap ring as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. Remove the vertical seat adjuster knob RH.


6. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

  1. B278171E01
    Raise the reclining adjuster release handle LH to reveal the claw. Using a screwdriver, detach the claw and remove the reclining adjuster release handle LH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


7. REMOVE FRONT SEAT CUSHION SHIELD LH

B278172E01
  1. Remove the 2 screws.

  1. Detach the 2 hooks in the order shown in the illustration, and then detach the guide and remove the front seat cushion shield LH.

    Text in Illustration 
    *1
    Hook
    *2
    Guide


8. REMOVE SEATBACK SPRING LH

  1. B277649
    Remove the seatback spring LH.


9. REMOVE ADJUSTER TUBE LH (for RHD, for Walk in Seat Type)

  1. B276716
    Remove the adjuster tube LH from the seatback spring LH.


10. REMOVE SEAT TRACK CONTROL CABLE BRACKET LH (for RHD, for Walk in Seat Type)

B276718
  1. Using a screwdriver, remove the E-ring.

  1. Detach the hook and remove the seat track control cable bracket LH.


11. REMOVE SEAT TRACK CONTROL CABLE BRACKET RH (for RHD, for Walk in Seat Type)

HINT:
Use the same procedure described for the LH side.


12. REMOVE FRONT SEATBACK HINGE PLATE (for RHD, for Walk in Seat Type)

  1. B276720
    Remove the front seatback hinge plate.


13. REMOVE NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY LH (for RHD, for Walk in Seat Type)

  1. B276722
    Detach the hook and remove the No. 1 fold seat lock control cable assembly LH.


14. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

  1. B278534
    Detach the 3 front seat airbag wire harness clamps.

  1. B278535
    Remove the hog rings and fold back the separate type front seat cushion cover and rubber bands of the separate type front seatback cover.

  1. B278537
    for LHD, w/ Seat Heater System:
    Disconnect the front seatback heater assembly LH connector.

  1. B278538
    Remove the 4 bolts and separate type front seatback assembly.


15. REMOVE SEPARATE TYPE FRONT SEATBACK COVER

  1. B278539E01
    Remove the hog rings and detach the 2 pieces of fastening tape.
    Text in Illustration 
    *1
    Fastening Tape

  1. Pass the front seat airbag wire harness through the hole of the separate type front seatback cover, and then roll up the separate type front seatback cover.

  1. B278174
    Remove the hog rings and detach the 2 straps of the separate type front seatback cover, and then roll up the separate type front seatback cover.

  1. B278175
    Pass the strap of the separate type front seatback cover through the holes of the separate type front seatback pad.

  1. B278541
    Remove the nut and detach the separate type front seatback cover bracket.

  1. Remove the hog rings and roll up the separate type front seatback cover.

    B284708E01

    Text in Illustration 
    *a
    Front view of front seatback
    *b
    Rear view of front seatback

  1. B207089
    Detach the 4 claws and remove the 2 front seat headrest supports and separate type front seatback cover from the separate type front seatback pad.


16. REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (for LHD, w/ Seat Heater System)

  1. B284710
    Cut off the tack pins which hold down the front seatback heater assembly LH, and then remove the front seatback heater assembly LH from the separate type front seatback cover.

    NOTICE:
    Be careful not to damage the separate type front seatback cover.


17. REMOVE SEPARATE TYPE FRONT SEATBACK PAD

  1. B207090
    Remove the separate type front seatback pad from the separate type front seatback spring assembly.


18. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER

  1. B284711
    for LHD, w/ Seat Heater System:
    Detach the 3 front seat cushion heater assembly LH wire harness clamps.

  1. B278178
    for Front Passenger Side, w/ Seat Belt Warning System:
    Detach the wire harness clamp.

  1. B278179
    Remove the hog rings.

  1. B278180
    Bend the 2 front seat cushion frame claws upward.

  1. Detach the hooks and remove the separate type front seat cushion cover together with the pad from the front seat cushion frame sub-assembly LH.

    B278181

  1. B207624
    Remove the hog rings and separate type front seat cushion cover from the separate type front seat cushion pad.


19. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (for LHD, w/ Seat Heater System)

  1. B284712
    Cut off the tack pins which hold down the front seat cushion heater assembly LH, and then remove the front seat cushion heater assembly LH from the separate type front seat cushion cover.

    NOTICE:
    Be careful not to damage the separate type front seat cushion cover.


20. REMOVE FRONT SEAT CUSHION PROTECTOR

  1. B276737
    Remove the 2 front seat cushion protectors.


21. REMOVE FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH

  1. B276739
    Remove the 4 bolts and front seat cushion frame sub-assembly LH from the lower reclining adjuster arm sub-assembly RH and the lower reclining adjuster arm sub-assembly LH.


22. REMOVE FRONT SEAT ADJUSTER ROD (for RHD, w/ Vertical Adjuster)

  1. B278182
    Remove the 2 bolts and front seat adjuster rod.


23. REMOVE SEAT TRACK HANDLE SUB-ASSEMBLY LH

  1. B278183
    B278184
    Using a screwdriver, detach the 2 springs and remove the seat track handle sub-assembly LH as shown in the illustration.

    HINT:
    The seat track handle sub-assembly LH will get caught on the springs when removing it. Detach the springs to remove the seat track handle sub-assembly LH.


24. REMOVE SEAT SPRING (for RHD, w/ Vertical Adjuster)
  1. Temporarily install the vertical seat adjuster knob RH.

  1. Turn the vertical seat adjuster knob RH clockwise and move the lower reclining adjuster arm sub-assembly to the uppermost position.

  1. Remove the vertical seat adjuster knob RH.

  1. B276740
    Detach the seat spring from the lower reclining adjuster arm sub-assembly.

  1. B276741
    Using a screwdriver, spread apart the tabs that hold the spring, and then remove the seat spring.


25. REMOVE FRONT NO. 2 SEAT ADJUSTER PIN RH (for RHD, w/ Vertical Adjuster)

  1. B276743
    Using a 6 mm socket hexagon wrench, remove the front No. 2 seat adjuster pin RH.


26. REMOVE VERTICAL ADJUSTING SHAFT SUB-ASSEMBLY (for RHD, w/ Vertical Adjuster)
  1. Temporarily install the vertical seat adjuster knob RH.

  1. B276742
    Turn the vertical seat adjuster knob RH counterclockwise and move the gear of the vertical adjusting shaft sub-assembly to the position shown in the illustration.

  1. Remove the vertical seat adjuster knob RH.

  1. B276744E01
    Using a screwdriver, remove the 2 E-rings.

  1. Disconnect the 2 vertical travel links from the vertical adjusting shaft sub-assembly.

    Text in Illustration 
    *1
    Vertical Travel Link

  1. B276746
    Disconnect the vertical adjusting shaft sub-assembly from the 2 lower reclining adjuster arms and remove the vertical adjusting shaft sub-assembly.


27. REMOVE LOWER RECLINING ADJUSTER ARM SUB-ASSEMBLY LH

  1. B276749
    for RHD, w/ Vertical Adjuster:
    Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts and lower reclining adjuster arm sub-assembly LH.

  1. B276750
    w/o Vertical Adjuster:
    Remove the 3 bolts and lower reclining adjuster arm sub-assembly LH.


28. REMOVE LOWER RECLINING ADJUSTER ARM SUB-ASSEMBLY RH
  1. for RHD, w/ Vertical Adjuster:

    HINT:
    Use the same procedure described for the LH side.

  1. w/o Vertical Adjuster:

    HINT:
    Use the same procedure described for the LH side.


29. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR LH

  1. B278193
    Remove the front seat cushion edge protector LH.


30. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR RH (for RHD, w/ Vertical Adjuster)

HINT:
Use the same procedure described for the LH side.


31. REMOVE NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY RH (for RHD, for Walk in Seat Type)

  1. B276752
    Detach the hook and remove the No. 1 fold seat lock control cable assembly RH.


32. REMOVE SEAT TRACK COVER SPRING (for RHD, for Walk in Seat Type)
  1. Operate the lock lever of the front seat outer track assembly so that the front seat outer track assembly is in the position shown in the illustration.

    CAUTION:
    When operating the lock lever of the front seat outer track assembly, the front seat outer track upper sub-assembly will suddenly move from the force of the spring. Therefore, hold down the front seat outer track upper sub-assembly while operating the lock lever of the front seat outer track assembly.

  1. Remove the seat track cover spring.

    B276754E01

    Text in Illustration 
    *1
    Lock Lever
    -
    -

← REMOVAL (from Aug 2013)DISASSEMBLY (Aug 2012 – Jul 2013) →