2014 Hilux · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. INSTALL SEAT TRACK COVER SPRING (for RHD, for Walk in Seat Type)
  1. Install the seat track cover spring.

  1. Operate the lock lever of the front seat outer track assembly so that the front seat outer track assembly is as shown in the illustration.

    B276755E01

    Text in Illustration 
    *1
    Lock Lever
    -
    -


2. INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY RH (for RHD, for Walk in Seat Type)
  1. Attach the hook to install the No. 1 fold seat lock control cable assembly RH.


3. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

  1. B278193
    Install the front seat cushion edge protector LH as shown in the illustration.


4. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for RHD, w/ Vertical Adjuster)

HINT:
Use the same procedure described for the LH side.


5. INSTALL LOWER RECLINING ADJUSTER ARM SUB-ASSEMBLY LH

  1. B276756
    for RHD, w/ Vertical Adjuster:

    1. Apply MP grease to the locations shown in the illustration.

      Text in Illustration 
      V100135
      MP Grease

  1. Using a T40 "TORX" socket wrench, install the lower reclining adjuster arm sub-assembly LH with the 2 "TORX" bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. w/o Vertical Adjuster:
    Install the lower reclining adjuster arm sub-assembly LH with the 3 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }


6. INSTALL LOWER RECLINING ADJUSTER ARM SUB-ASSEMBLY RH
  1. for RHD, w/ Vertical Adjuster:

    HINT:
    Use the same procedure described for the LH side.

  1. w/o Vertical Adjuster:

    HINT:
    Use the same procedure described for the LH side.

  1. for RHD, for Walk in Seat Type:

    HINT:
    1. Use the same procedure described for the LH side.

    2. B276751
      Set the No. 1 fold seat lock control cable assembly RH as shown in the illustration.


7. INSTALL VERTICAL ADJUSTING SHAFT SUB-ASSEMBLY (for RHD, w/ Vertical Adjuster)

  1. B276757
    Apply MP grease to the locations shown in the illustration.
    Text in Illustration 
    V100135
    MP Grease

  1. B276747
    Connect the vertical adjusting shaft sub-assembly to the 2 lower reclining adjuster arms to install it.

  1. B276745E01
    Connect the 2 vertical travel links to the vertical adjusting shaft sub-assembly.
    Text in Illustration 
    *1
    Vertical Travel Link

  1. Install 2 new E-rings.

  1. Temporarily install the vertical seat adjuster knob RH.

  1. B276758E01
    Turn the vertical seat adjuster knob RH as much as possible in the direction indicated by arrow A in the illustration.
    Text in Illustration 
    *1
    Vertical Adjusting Shaft Sub-assembly
    *2
    Lower Reclining Adjuster Arm Sub-assembly
    *3
    Hole
    *a
    Arrow A
    *b
    Arrow B

  1. Mesh the gear of the vertical adjusting shaft sub-assembly with the gear of the lower reclining adjuster arm sub-assembly.

  1. Align the holes of the vertical adjusting shaft sub-assembly and lower reclining adjuster arm sub-assembly by turning the vertical seat adjuster knob RH in the direction indicated by arrow B in the illustration.

  1. Remove the vertical seat adjuster knob RH.


8. INSTALL FRONT NO. 2 SEAT ADJUSTER PIN RH (for RHD, w/ Vertical Adjuster)
  1. Using a 6 mm socket hexagon wrench, install the front No. 2 seat adjuster pin RH.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


9. INSTALL SEAT SPRING (for RHD, w/ Vertical Adjuster)
  1. Temporarily install the vertical seat adjuster knob RH.

  1. Turn the vertical seat adjuster knob RH clockwise and move the lower reclining adjuster arm sub-assembly to the uppermost position.

  1. Remove the vertical seat adjuster knob RH.

  1. B286711
    Install the seat spring as shown in the illustration.

  1. Using pliers, push together the tabs that hold the seat spring.

  1. B286712
    Attach the seat spring to the lower reclining adjuster arm sub-assembly.


10. INSTALL SEAT TRACK HANDLE SUB-ASSEMBLY LH

  1. B278199
    Apply MP grease to the locations shown in the illustration.
    Text in Illustration 
    V100135
    MP Grease

  1. B278200
    B278184
    Attach the 2 springs to install the seat track handle sub-assembly LH as shown in the illustration.

    HINT:
    The seat track handle sub-assembly LH will get caught on the springs when installing it. Detach the springs to install the seat track handle sub-assembly LH.


11. INSTALL FRONT SEAT ADJUSTER ROD (for RHD, w/ Vertical Adjuster)
  1. Install the front seat adjuster rod with the 2 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }


12. INSTALL FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH
  1. Install the front seat cushion frame sub-assembly LH to the lower reclining adjuster arm sub-assembly RH and the lower reclining adjuster arm sub-assembly LH with the 4 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }


13. INSTALL FRONT SEAT CUSHION PROTECTOR

  1. B276738
    Install the 2 front seat cushion protectors.


14. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (for LHD, w/ Seat Heater System)

B284714E01
  1. Set the front seat cushion heater on the separate type front seat cushion cover.

  1. Using a tacker, install the front seat cushion heater to the separate type front seat cushion cover with 12 new tack pins as shown in the illustration.

    NOTICE:
    Do not substitute other metal parts for tack pins.

    Text in Illustration 
    *1
    Tack Pin
    *2
    Separate Type Front Seat Cushion Cover
    *3
    Front Seat Cushion Heater Assembly LH


15. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

  1. B207627E02
    Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers

  1. Attach the hooks to install the separate type front seat cushion cover with pad to the front seat cushion frame sub-assembly LH.

  1. B276735
    Bend the 2 front seat cushion frame claws downward.

  1. B278201E01
    Using hog ring pliers, attach the separate type front seat cushion cover to the front seat cushion frame sub-assembly LH with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

  1. B278178
    for Front Passenger Side, w/ Seat Belt Warning System:
    Attach the wire harness clamp.

  1. B284711
    for LHD, w/ Seat Heater System:
    Attach the 3 front seat cushion heater assembly LH wire harness clamps.


16. INSTALL SEPARATE TYPE FRONT SEATBACK PAD

  1. B207459
    Install the separate type front seatback pad to the separate type front seatback spring assembly.


17. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (for LHD, w/ Seat Heater System)
  1. Set the front seatback heater assembly LH on the separate type front seatback cover.

  1. Using a tacker, install the front seatback heater assembly LH to the separate type front seatback cover with 6 new tack pins as shown in the illustration.

    NOTICE:
    Do not substitute other metal parts for tack pins.


    B284713E01
    Text in Illustration 
    *1
    Tack Pin
    *2
    Separate Type Front Seatback Cover
    *3
    Listing Pocket of Separate Type Front Seatback Cover
    -
    -


18. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.


    B284709E01
    Text in Illustration 
    *1
    Hog Ring Pliers
    -
    -
    *a
    Front view of front seatback
    *b
    Rear view of front seatback

  1. Attach the 4 claws to install the 2 front seat headrest supports.

  1. B284707
    Attach the separate type front seatback cover bracket and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    After the separate type front seatback cover is installed, make sure the separate type front seatback cover bracket is not twisted.

  1. B277651
    Pass the straps of the separate type front seatback cover through the holes of the separate type front seatback pad.

  1. B209095E03
    Using hog ring pliers, attach the 2 straps of the separate type front seatback cover to the separate type front seatback spring assembly with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

  1. B278540E01
    Pass the front seat airbag wire harness through the hole of the separate type front seatback cover.

  1. Using hog ring pliers, attach the separate type front seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Attach the 2 pieces of fastening tape.

    Text in Illustration 
    *1
    Hog Ring Pliers
    *2
    Fastening Tape


19. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
  1. Install the separate type front seatback assembly with the 4 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. B278537
    for LHD, w/ Seat Heater System:
    Connect the front seatback heater assembly LH connector.

  1. B286713E01
    Using hog ring pliers, attach the separate type front seat cushion cover and rubber bands of the separate type front seatback cover to the front seat cushion frame sub-assembly LH with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

  1. B278534
    Attach the 3 front seat airbag wire harness clamps.


20. INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY LH (for RHD, for Walk in Seat Type)
  1. Attach the hook to install the No. 1 fold seat lock control cable assembly LH.


21. INSTALL FRONT SEATBACK HINGE PLATE (for RHD, for Walk in Seat Type)

  1. B276762
    Apply MP grease to the location shown in the illustration.
    Text in Illustration 
    V100135
    MP Grease

  1. B276721
    Install the front seatback hinge plate.


22. INSTALL SEAT TRACK CONTROL CABLE BRACKET LH (for RHD, for Walk in Seat Type)

  1. B276761
    Apply MP grease to the location shown in the illustration.
    Text in Illustration 
    V100135
    MP Grease

  1. B276719
    Attach the hook to install the seat track control cable bracket LH.

  1. Install a new E-ring.


23. INSTALL SEAT TRACK CONTROL CABLE BRACKET RH (for RHD, for Walk in Seat Type)

HINT:
Use the same procedure described for the LH side.


24. INSTALL ADJUSTER TUBE LH (for RHD, for Walk in Seat Type)

  1. B276717
    Install the adjuster tube LH to the seatback spring LH.


25. INSTALL SEATBACK SPRING LH

  1. B277652
    Install the seatback spring LH.


26. INSTALL FRONT SEAT CUSHION SHIELD LH

B278205E01
  1. Attach the guide and 2 hooks in the order shown in the illustration to install the front seat cushion shield LH.

    Text in Illustration 
    *1
    Guide
    *2
    Hook

  1. Install the 2 screws.


27. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

  1. B278206
    Attach the claw to install the reclining adjuster release handle LH.


28. INSTALL VERTICAL SEAT ADJUSTER KNOB RH (for RHD, w/ Vertical Adjuster)

B108452
  1. Install the snap ring to the vertical seat adjuster knob RH.

  1. Install the vertical seat adjuster knob RH.


29. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

B278208E01
  1. Attach the 2 hooks in the order shown in the illustration to install the front seat inner cushion shield LH.

  1. Install the 2 screws.


30. INSTALL FRONT SEAT CUSHION COVER LH
  1. Install the front seat cushion cover LH.


31. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)
(Click here)

32. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)
(Click here)
← DISASSEMBLY (from Aug 2013)REASSEMBLY (Aug 2012 – Jul 2013) →