Apply MP grease to the locations shown in the illustration.
Text in Illustration
MP Grease
Connect the vertical adjusting shaft sub-assembly to the 2 lower reclining adjuster arms to install it.
Connect the 2 vertical travel links to the vertical adjusting shaft sub-assembly.
Text in Illustration
*1
Vertical Travel Link
Install 2 new E-rings.
Temporarily install the vertical seat adjuster knob LH.
Turn the vertical seat adjuster knob LH as much as possible in the direction indicated by arrow A in the illustration.
Text in Illustration
*1
Vertical Adjusting Shaft Sub-assembly
*2
Lower Reclining Adjuster Arm Sub-assembly
*3
Hole
*a
Arrow A
*b
Arrow B
Mesh the gear of the vertical adjusting shaft sub-assembly with the gear of the lower reclining adjuster arm sub-assembly.
Align the holes of the vertical adjusting shaft sub-assembly and lower reclining adjuster arm sub-assembly by turning the vertical seat adjuster knob LH in the direction indicated by arrow B in the illustration.
Using a 6 mm socket hexagon wrench, install the front No. 2 seat adjuster pin LH.
Torque:
8.0 N*m{
82 kgf*cm
, 71 in.*lbf
}
9.
INSTALL SEAT SPRING (w/ Vertical Adjuster)
Temporarily install the vertical seat adjuster knob LH.
Turn the vertical seat adjuster knob LH clockwise and move the lower reclining adjuster arm sub-assembly to the uppermost position.
Remove the vertical seat adjuster knob LH.
Install the seat spring as shown in the illustration.
Using pliers, push together the tabs that hold the seat spring.
Attach the seat spring to the lower reclining adjuster arm sub-assembly.
10.
INSTALL SEAT TRACK HANDLE SUB-ASSEMBLY LH
Apply MP grease to the locations shown in the illustration.
Text in Illustration
MP Grease
Attach the 2 springs to install the seat track handle sub-assembly LH as shown in the illustration.
HINT:
The seat track handle sub-assembly LH will get caught on the springs when installing it. Detach the springs to install the seat track handle sub-assembly LH.
11.
INSTALL FRONT SEAT ADJUSTER ROD (w/ Vertical Adjuster)
Install the front seat adjuster rod with the 2 bolts.
Torque:
20 N*m{
199 kgf*cm
, 14 ft.*lbf
}
12.
INSTALL FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH
Install the front seat cushion frame sub-assembly LH to the lower reclining adjuster arm sub-assembly RH and the lower reclining adjuster arm sub-assembly LH with the 4 bolts.
Set the front seat cushion heater on the separate type front seat cushion cover.
Using a tacker, install the front seat cushion heater to the separate type front seat cushion cover with 12 new tack pins as shown in the illustration.
NOTICE:
Do not substitute other metal parts for tack pins.
Text in Illustration
*1
Tack Pin
*2
Separate Type Front Seat Cushion Cover
*3
Front Seat Cushion Heater Assembly LH
15.
INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Text in Illustration
*A
for Vinyl Seat, for Cloth Seat
*B
for Leather Seat
*1
Hog Ring Pliers
-
-
Attach the hooks to install the separate type front seat cushion cover with pad to the front seat cushion frame sub-assembly LH.
Bend the 2 front seat cushion frame claws downward.
Using hog ring pliers, attach the separate type front seat cushion cover to the front seat cushion frame sub-assembly LH with new hog rings.
Text in Illustration
*1
Hog Ring Pliers
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
for Front Passenger Side, w/ Seat Belt Warning System: Attach the wire harness clamp.
for LHD, w/ Seat Heater System: Attach the 3 front seat cushion heater assembly LH wire harness clamps.
16.
INSTALL SEPARATE TYPE FRONT SEATBACK PAD
Install the separate type front seatback pad to the separate type front seatback spring assembly.
Set the front seatback heater assembly LH on the separate type front seatback cover.
Using a tacker, install the front seatback heater assembly LH to the separate type front seatback cover with 6 new tack pins as shown in the illustration.
NOTICE:
Do not substitute other metal parts for tack pins.
Text in Illustration
*1
Tack Pin
*2
Separate Type Front Seatback Cover
*3
Listing Pocket of Separate Type Front Seatback Cover
-
-
18.
INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Text in Illustration
*A
for Vinyl Seat, for Cloth Seat
*B
for Leather Seat
*1
Hog Ring Pliers
-
-
*a
Front view of front seatback
*b
Rear view of front seatback
Attach the 4 claws to install the 2 front seat headrest supports.
Pass the straps of the separate type front seatback cover through the holes of the separate type front seatback pad.
Using hog ring pliers, attach the 2 straps of the separate type front seatback cover to the separate type front seatback spring assembly with new hog rings.
Text in Illustration
*1
Hog Ring Pliers
Using hog ring pliers, attach the separate type front seatback cover with new hog rings.
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Attach the 2 pieces of fastening tape.
Text in Illustration
*1
Hog Ring Pliers
*2
Fastening Tape
Install the front seatback assembly with the 4 bolts.
Torque:
40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
for LHD, w/ Seat Heater System: Connect the front seatback heater assembly LH connector.
Using hog ring pliers, attach the separate type front seat cushion cover to the front seat cushion frame sub-assembly LH with new hog rings.
Text in Illustration
*1
Hog Ring Pliers
NOTICE:
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
19.
INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY RH (for Walk in Seat Type)
Attach the hook to install the No. 1 fold seat lock control cable assembly RH.
20.
INSTALL FRONT SEATBACK HINGE PLATE (for Walk in Seat Type)
Apply MP grease to the location shown in the illustration.
Text in Illustration
MP Grease
Install the front seatback hinge plate.
21.
INSTALL SEAT TRACK CONTROL CABLE BRACKET RH (for Walk in Seat Type)
Apply MP grease to the location shown in the illustration.
Text in Illustration
MP Grease
Attach the hook to install the seat track control cable bracket RH.
Install a new E-ring.
22.
INSTALL SEAT TRACK CONTROL CABLE BRACKET LH (for Walk in Seat Type)
HINT:
Use the same procedure described for the RH side.
23.
INSTALL ADJUSTER TUBE RH (for Walk in Seat Type)
Install the adjuster tube RH to the seatback spring RH.
24.
INSTALL SEATBACK SPRING LH
Install the seatback spring LH.
25.
INSTALL FRONT SEAT CUSHION SHIELD LH
Attach the guide and 2 hooks in the order shown in the illustration to install the front seat cushion shield LH.
Text in Illustration
*1
Guide
*2
Hook
Install the 2 screws.
26.
INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
Attach the claw to install the reclining adjuster release handle LH.