2014 Hilux · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.


1. INSTALL REAR SEAT ASSEMBLY

  1. except 3 Point Type Rear Center Seat Belt:

    1. Fold up the rear seat cushion assembly.

    2. B276877E01
      Place the rear seat assembly in the cabin.

      NOTICE:
      Be careful not to damage the vehicle body.

    3. Attach the 2 hooks and 2 guides.

      Text in Illustration 
      *1
      Hook
      *2
      Guide

    4. Attach the fold seat stopper band to the vehicle body and temporarily fix the rear seat cushion assembly in place.

    5. Temporarily install the rear seat assembly with the 4 bolts.

    6. Tighten the 4 bolts in the order shown in the illustration.

      Torque:
      20 N*m{ 199 kgf*cm , 14 ft.*lbf }

    7. B276878E01
      Pass the 2 rear No. 1 seat inner belts through the 2 seat cushion rubber bands.
      Text in Illustration 
      *1
      Seat Cushion Rubber Band

    8. B277835E01
      Return the seat cushion to its original position to lock the seat cushion lock.

    9. Attach the fold seat stopper band button.

      Text in Illustration 
      *1
      Fold Seat Stopper Band Button

  1. for 3 Point Type Rear Center Seat Belt:

    1. Fold up the rear seat cushion assembly.

    2. B360163E01
      Place the rear seat assembly in the cabin.

      NOTICE:
      Be careful not to damage the vehicle body.

    3. Attach the 2 hooks and 2 guides.

      Text in Illustration 
      *1
      Hook
      *2
      Guide

    4. Attach the fold seat stopper band to the vehicle body and temporarily fix the rear seat cushion assembly in place.

    5. Temporarily install the rear seat assembly with the 4 bolts.

    6. Tighten the 4 bolts in the order shown in the illustration.

      Torque:
      20 N*m{ 199 kgf*cm , 14 ft.*lbf }

    7. Return the seat cushion to its original position.

    8. B360164E01
      Pass the rear No. 1 seat inner belt assembly LH through the seat cushion rubber band.
      Text in Illustration 
      *1
      Seat Cushion Rubber Band

    9. Fold up the rear seat cushion assembly.

    10. B360166E01
      Connect the rear No. 1 seat inner belt assembly LH with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      1. Do not overlap the anchor part of the rear No. 1 seat inner belt assembly LH and protruding parts of the vehicle body.
      2. Make sure that the arrow on the rear No. 1 seat inner belt assembly LH floor anchor is facing towards the front of the vehicle.
      3. Connect the rear No. 1 seat inner belt assembly LH so that the angle of the floor anchor is with in the standard range.

        Standard:
        0° to 5°

      Text in Illustration 
      *1
      Protruding Part
      *2
      Floor Anchor
      *3
      Arrow
      *a
      Vehicle Front (0°)
      *b
      5°

    11. B360167E01
      Pass the rear No. 1 seat inner belt assembly RH through the seat cushion rubber band.
      Text in Illustration 
      *1
      Seat Cushion Rubber Band

    12. B360165E01
      Lock the seat cushion lock.

    13. Attach the fold seat stopper band button.

      Text in Illustration 
      *1
      Fold Seat Stopper Band Button


2. INSTALL REAR SEAT HINGE COVER LH

  1. B276875
    Attach the guide.

  1. Push the rear seat hinge cover LH to attach the 2 claws and install the rear seat hinge cover LH.


3. INSTALL REAR SEAT HINGE COVER RH

HINT:
Use the same procedures described for the LH side.

← INSTALLATION (Jun 2011 – Jul 2013)COMPONENTS (from Jun 2011) →