2014 Hilux · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Jun 2011

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.


1. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY

  1. B276907E01
    Connect and rotate a new connecting wire to the No. 1 seat cushion frame lock plate.
    Text in Illustration 
    *1
    No. 1 Seat Cushion Frame Lock Plate

  1. B277847
    Connect the fold seat stopper band assembly to the connecting wire.

  1. B276905
    Using needle nose pliers, bend the ends of the connecting wire together.

  1. B276901
    Return the fold seat stopper band assembly to its original position.


2. INSTALL NO. 1 SEAT CUSHION PAD

  1. B276899
    Install the No. 1 seat cushion pad to the No. 1 seat cushion frame.


3. INSTALL NO. 1 SEAT CUSHION COVER

B276895
  1. Pass the fold seat stopper band assembly through the 2 holes of the No. 1 seat cushion cover to the surface.

  1. B276897E01
    Using hog ring pliers, install the center of the No. 1 seat cushion cover to the No. 1 seat cushion pad with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

  1. for TSAM Made:

    1. B257931E02
      Close the 2 fasteners.
      Text in Illustration 
      *1
      Hog Ring Pliers
      *2
      Fastener

    2. Using hog ring pliers, attach the 2 wires at the rear of the No. 1 seat cushion cover with new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.

  1. for TMT Made:

    1. B257923E02
      Close the 2 fasteners.
      Text in Illustration 
      *1
      Hog Ring Pliers
      *2
      Fastener

    2. Using hog ring pliers, attach the 2 wires at the rear of the No. 1 seat cushion cover with new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.


4. INSTALL REAR SEAT CUSHION

B277932
  1. Install the 2 rear seat cushions with the 2 screws.


5. INSTALL NO. 1 SEATBACK PAD

  1. B276890
    Install a new No. 1 seatback pad to the No. 1 seatback frame.


6. INSTALL NO. 1 SEATBACK COVER

B276888E01
  1. Using hog ring pliers, install the center of the No. 1 seatback cover to the No. 1 seatback pad with new hog rings.

    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B276883E01
    Using hog ring pliers, install the No. 1 seatback cover to the No. 1 seatback frame with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.


7. INSTALL REAR SEATBACK ASSEMBLY

  1. B276881
    Install the rear seatback assembly to the rear seat cushion assembly with the 2 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }


8. INSTALL REAR SEAT HEADREST SUPPORT

  1. B276886
    w/o Center Headrest:
    Attach the 8 claws to install the 4 rear seat headrest supports.

  1. B288337
    w/ Center Headrest:
    Attach the 12 claws to install the 6 rear seat headrest supports.


9. INSTALL REAR SEAT CUSHION COVER LH

B276910E01
  1. Attach the guide.

  1. Install the rear seat cushion cover LH with the screw.

  1. If the washer was installed between the rear seat leg bracket LH and rear seat cushion cover LH:
    Install the washer.

    Text in Illustration 
    *a
    Washer installed between rear seat leg bracket LH and rear seat cushion cover LH


10. INSTALL REAR SEAT LEG BRACKET LH

B276884E01
  1. If the washer was installed between the nut and rear seat leg bracket LH:
    Temporarily install the rear seat leg bracket LH and washer with the nut.

    Text in Illustration 
    *a
    Washer installed between nut and rear seat leg bracket LH

  1. If the washer was not installed between the nut and rear seat leg bracket LH:
    Temporarily install the rear seat leg bracket LH with the nut.

  1. Tighten the nut.

    Torque:
    15 N*m{ 148 kgf*cm , 11 ft.*lbf }


11. INSTALL REAR SEAT CUSHION COVER RH

HINT:
Use the same procedures described for the LH side.


12. INSTALL REAR SEAT LEG BRACKET RH

HINT:
Use the same procedures described for the LH side.


13. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Headrest)
  1. Install the rear center seat headrest assembly.


14. INSTALL REAR SEAT HEADREST ASSEMBLY
  1. Install the 2 rear seat headrests.

← DISASSEMBLY (from Jun 2011)INSTALLATION (Jun 2011 – Jul 2013) →