2014 Hilux · Service Manual ENGINE

Starter Signal Circuit

Circuit diagnosis · Vehicles built Jun 2011 – Oct 2011

Versions by build date: Jun 2011 – Oct 2011 from Nov 2011

DESCRIPTION

When the engine is cranked, the intake air flow becomes slow, so fuel vaporization is poor. A rich mixture is therefore necessary in order to achieve good startability. While the engine is being cranked, the battery voltage is applied to terminal STA of the ECM. The starter signal is mainly used to increase the fuel injection volume for starting and after-start injection control.

WIRING DIAGRAM

A261034E01

INSPECTION PROCEDURE


When using intelligent tester:


1. READ VALUE USING INTELLIGENT TESTER (STA SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the STA signal on the intelligent tester while the starter operates.

    Result:
    Ignition Switch Position
    STA Signal
    LOCK, ACC, ON
    OFF
    STA
    ON



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2. INSPECT FUSE (ST)

  1. A121916E01
    Remove the ST fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Tester Connection
    Specified Condition
    ST fuse
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


3. CHECK WIRE HARNESS (IGNITION SWITCH - ST FUSE, ST FUSE - ECM)

  1. A121938E01
    Check the wire harness between the ignition switch and ST fuse.
    1. Disconnect the ignition switch connector.

    2. Remove the ST fuse from the instrument panel junction block.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      I6-7 (ST2) - Instrument panel junction block ST fuse terminal 1
      Below 1 Ω
      I6-7 (ST2) - Instrument panel junction block ST fuse terminal 1 - Body ground
      10 kΩ or higher

  1. A121939E01
    Check the wire harness between the ST fuse and ECM.
    1. Remove the ST fuse from the instrument panel junction block.

    2. Disconnect the E20 ECM connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      Instrument panel junction block ST fuse terminal 2 - E20-11 (STA)
      Below 1 Ω
      Instrument panel junction block ST fuse terminal 2 or E20-11 (STA) - Body ground
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM


When not using intelligent tester:


1. CHECK ECM (STA VOLTAGE)
A062416E39
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E20-11 (STA) - E23-14 (E1)
    Cranking
    6 V or more



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2. INSPECT FUSE (ST)

  1. A121916E01
    Remove the ST fuse from the instrument panel junction block.

  1. Measure the resistance of the ST fuse.

    Standard resistance:
    Tester Connection
    Specified Condition
    ST fuse
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


3. CHECK WIRE HARNESS (IGNITION SWITCH - ST FUSE, ST FUSE - ECM)

  1. A121938E01
    Check the wire harness between the ignition switch and ST fuse.
    1. Disconnect the ignition switch connector.

    2. Remove the ST fuse from the instrument panel junction block.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      I6-7 (ST2) - Instrument panel junction block ST fuse terminal 1
      Below 1 Ω
      I6-7 (ST2) - Instrument panel junction block ST fuse terminal 1 - Body ground
      10 kΩ or higher

  1. A121939E01
    Check the wire harness between the ST fuse and ECM.
    1. Remove the ST fuse from the instrument panel junction block.

    2. Disconnect the E20 ECM connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      Instrument panel junction block ST fuse terminal 2 - E20-11 (STA)
      Below 1 Ω
      Instrument panel junction block ST fuse terminal 2 or E20-11 (STA) - Body ground
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM


← ECM Power Source Circuit (from Jun 2011)Starter Signal Circuit (from Nov 2011) →