2014 Hilux · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. INSPECT UNIVERSAL JOINT SPIDER ASSEMBLY
  1. Check the spider bearings for wear or damage.

  1. Check each spider bearing's axial play by turning the yoke while holding the shaft tightly.

    Maximum bearing axial play:
    0 to 0.05 mm (0 to 0.002 in.)

    If the axial play is greater than the maximum, replace the spider bearing.


2. REMOVE REAR SLIDING SHAFT BOOT (for 4WD)
  1. Place matchmarks on the propeller shaft and sleeve yoke.

  1. Using a side cutter or pliers, remove the small and large boot clamps.

  1. Disconnect the boot from the sleeve yoke.

  1. Remove the sleeve yoke, and then remove the boot from the propeller shaft.


3. REMOVE UNIVERSAL JOINT SPIDER ASSEMBLY

F052432E01
  1. Place matchmarks on the yokes.

  1. C118615E01
    Place matchmarks on the center yoke and the part it is connected to (yoke or shaft).

  1. F052433E01
    Using a brass bar and hammer, slightly tap in the spider bearing outer races.

  1. Using needle nose pliers, remove the 4 snap rings from the grooves.

  1. F015025E01
    Clamp the propeller shaft in a vise between aluminum plates.

  1. Using SST, push the sleeve yoke side spider bearing until: 1) the spider almost touches the sleeve yoke or propeller shaft, and 2) the spider bearing on the opposite side is partially pushed out.

    SST
    09332-25010  

    HINT:
    Before installing SST, sufficiently raise the part labeled A. If part A is too low, SST may be difficult to install.

  1. F044192E01
    Clamp the pushed out spider bearing outer race in a vise and tap the propeller shaft to remove the spider bearing.

    NOTICE:
    Do not tap the shaft tube.

    HINT:
    Remove the spider bearing from the opposite side of the spider using the same procedure.

  1. Separate the flange yoke and spider from the propeller shaft.

  1. F015030E01
    Reinstall the 2 removed spider bearings to the spider and clamp the spider bearings in a vise.

  1. Using SST, push the flange yoke side spider bearing until: 1) the spider almost touches the flange yoke, and 2) the spider bearing on the opposite side is partially pushed out.

    SST
    09332-25010  

    HINT:
    Before installing SST, sufficiently raise the part labeled A. If part A is too low, SST may be difficult to install.

  1. F044193E01
    Clamp the pushed out spider bearing outer race in a vise and tap the flange yoke to remove the spider bearing.

    HINT:
    Remove the spider bearing from the opposite side of the spider using the same procedure.

  1. Separate the spider from the flange yoke.

    HINT:
    Perform the removal of the other universal joint spider(s) using the same procedures.


4. REMOVE CENTER NO. 1 SUPPORT BEARING ASSEMBLY

C118616
  1. Clamp the center yoke in a vise between aluminum plates.

  1. Using a hammer and chisel, loosen the staked part of the nut and remove the nut and washer.

  1. C118617E01
    Place matchmarks on the intermediate shaft and center yoke.

  1. Using a brass bar and hammer, tap out the center yoke.

  1. Remove the washer and center support bearing from the intermediate shaft.


5. INSPECT CENTER NO. 1 SUPPORT BEARING ASSEMBLY

C118618
  1. When turning the center bearing with your hand, check that it turns smoothly without catching and that there are no cracks or damage.
    If there are any defects, replace it.
    If there are any damage to the lip of the center bearing case, replace it.


6. INSPECT PROPELLER SHAFT AND INTERMEDIATE SHAFT

C061260E02
  1. Using a dial indicator, measure the propeller shaft and intermediate shaft runout.

    Maximum runout:
    Item
    Specified Condition
    Propeller shaft
    0.8 mm (0.031 in.)
    Intermediate shaft
    0.8 mm (0.031 in.)

    If the runout is greater than the maximum, replace the shaft.

← REMOVAL (from Jun 2011)INSPECTION (from Jun 2011) →