Install a new gasket and the deflector to the axle shaft.
HINT:
Align the 3 oil drain holes.
for 2WD: Pass 5 new hub bolts through the axle hub.
for 4WD and Pre-Runner: Pass 6 new hub bolts through the axle hub.
Secure the axle shaft between aluminum plates in a vise.
for 2WD: Temporarily install a washer and nut to each of the 5 hub bolts as shown in the illustration.
for 4WD and Pre-Runner: Temporarily install a washer and nut to each of the 6 hub bolts as shown in the illustration.
Install the hub bolts by tightening each nut.
Remove the washer and nut from each hub bolt.
4.
INSTALL BACKING PLATE TO REAR AXLE HOUSING SETTING BOLT
Position the backing plate on the bearing case.
Using 2 socket wrenches and a press, press in 4 new setting bolts.
5.
INSTALL REAR AXLE BEARING INNER RETAINER LH
Heat a new retainer to approximately 70 to 130°C (158 to 266°F).
Install a new shaft washer and the retainer to the axle shaft as shown in the illustration.
NOTICE:
Install the shaft washer with its tapered surface facing downward.
Install the retainer with its chamfered surface facing downward.
Using SST and a press, press in the axle shaft.
SST
09951-01100 09631-12090 09726-40010
Using a snap ring expander, install a new snap ring.
6.
INSTALL REAR AXLE BEARING INNER RETAINER LH AND REAR SKID CONTROL ROTOR (w/ ABS, VSC)
Using SST and a press, press in a new skid control rotor and retainer to the axle shaft until the lengths are within the standard range.
SST
09951-01100 09631-12090 09726-40010
Standard length:
Length A
Length B
133.2 +/-0.6 mm (5.244 +/-0.0236 in.)
56 mm (2.205 in.)
NOTICE:
If this installation measurement is not followed precisely, oil leaks and other mechanical failures will result. Follow the assembly instructions closely, and confirm that parts have been installed according to the standard length measurement.
HINT:
It may be easier to verify the installation by adding the length of the SST to the standard length, and then measuring the height from the surface of the press.
Install the axle shaft with backing plate with the 4 nuts.
Torque:
43 N*m{
438 kgf*cm
, 32 ft.*lbf
}
10.
CONNECT PARKING BRAKE CABLE
Connect the parking brake cable with the 2 bolts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
11.
INSTALL REAR BRAKE SHOE (for 2WD)
Using needle-nose pliers, connect the No. 3 parking brake cable to the parking brake shoe lever.
Using needle-nose pliers, install the adjust lever tension spring to the automatic adjust lever and rear brake shoe.
Using SST, install the shoe, pin, shoe hold down spring and shoe hold down spring cup.
SST
09718-00010
12.
INSTALL FRONT BRAKE SHOE (for 2WD)
Connect the shoe tension spring to the front brake shoe and rear brake shoe.
Using SST, install the shoe, shoe hold down spring and shoe hold down spring cup.
SST
09718-00010
13.
INSTALL BRAKE SHOES (for 4WD and Pre-Runner)
Using needle-nose pliers, connect the No. 3 parking brake cable to the parking brake shoe lever.
Install the strut set and return spring to the shoe.
Attach the support clip to exposed threads of the strut set.
NOTICE:
The support clip shall not contact the adjuster nut.
Using needle-nose pliers, hook the support clip around the spring.
NOTICE:
Be careful not to damage the spring.
Install the front and rear brake shoes.
Move one of the shoes upward and install the shoe tension spring.
Install the shoe front or rear side to the cylinder. Then install the other side of the shoe to the other side of the cylinder.
HINT:
After one side of the shoe is installed to the cylinder, hold that side of the shoe steady. Then widen the opening of the shoe by pulling the other side of the shoe outward and install it to the other side of the cylinder.
NOTICE:
Be careful not to damage the cylinder dust boot.
Using pliers, install the front brake shoe, rear brake shoe, pins and shoe hold down springs.
14.
INSTALL REAR SPEED SENSOR LH (w/ ABS, VSC)
Install the speed sensor RH with the bolt.
Torque:
8.5 N*m{
87 kgf*cm
, 75 in.*lbf
}
NOTICE:
Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.
While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.
After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.
Install the harness clamp with the bolt.
Torque:
8.5 N*m{
87 kgf*cm
, 75 in.*lbf
}
NOTICE:
When installing the clamp, do not twist the wire harness.
Make sure the clamp rotation stopper touches the installation position.
Attach the 2 clamps.
NOTICE:
When attaching the clamps, do not twist the wire harness.
Attach the connector.
NOTICE:
Securely attach the connector.
When attaching the connector, do not twist the wire harness.
Connect the connector.
NOTICE:
Securely connect the connector.
When connecting the connector, do not twist the wire harness.
Install the speed sensor LH with the bolt.
Torque:
8.5 N*m{
87 kgf*cm
, 75 in.*lbf
}
NOTICE:
Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.
While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.
After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.
Install the 2 harness clamps with the 2 bolts.
Torque:
for bolt A:
8.5 N*m{
87 kgf*cm
, 75 in.*lbf
}
for bolt B:
32 N*m{
326 kgf*cm
, 24 ft.*lbf
}
NOTICE:
When installing the clamps, do not twist the wire harness.
Make sure the clamp rotation stopper touches the installation position.
Attach the clamp.
NOTICE:
When attaching the clamp, do not twist the wire harness.
15.
CONNECT BRAKE LINE (for 2WD)
Install the cylinder with the 2 bolts.
Torque:
9.5 N*m{
97 kgf*cm
, 84 in.*lbf
}
Using a union nut wrench, connect the brake line.
Torque:
15 N*m{
155 kgf*cm
, 11 ft.*lbf
}
NOTICE:
Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).
16.
CONNECT BRAKE LINE (for 4WD and Pre-Runner)
Install the cylinder with the 2 bolts.
Torque:
12 N*m{
117 kgf*cm
, 8 ft.*lbf
}
Using a union nut wrench, connect the brake line.
Torque:
15 N*m{
155 kgf*cm
, 11 ft.*lbf
}
NOTICE:
Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).