2014 Hilux · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built from Jun 2011

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE REAR WHEEL

3. DRAIN BRAKE FLUID (for 2WD)

NOTICE:
Wash off brake fluid immediately if it comes in contact with any painted surface.


4. DRAIN BRAKE FLUID (for 4WD and Pre-Runner)

NOTICE:
Wash off brake fluid immediately if it comes in contact with any painted surface.


5. DISCONNECT BRAKE LINE (for 2WD)

  1. C111485
    Using a union nut wrench, disconnect the brake line.

  1. Remove the 2 bolts and cylinder.


6. DISCONNECT BRAKE LINE (for 4WD and Pre-Runner)

C111505
  1. Using a union nut wrench, disconnect the brake line.

  1. Remove the 2 bolts and cylinder.


7. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for 2WD)
  1. Release the parking brake lever, and remove the drum.

    HINT:
    If the drum cannot be removed easily, perform the following procedures.

  1. C111394E01
    Remove the hole plug (adjust) and insert a screwdriver into the hole on the backing plate, and hold the automatic adjust lever away from the adjuster.

  1. Using another screwdriver, compress the brake shoe adjuster by turning the adjusting wheel.


8. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for 4WD and Pre-Runner)
  1. Release the parking brake lever, and remove the drum.

    HINT:
    If the drum cannot be removed easily, perform the following procedures.

  1. C111496E01
    Remove the hole plug (adjust) and insert a screwdriver into the hole on the backing plate, and hold the automatic adjust lever away from the adjuster.

  1. Using another screwdriver, compress the shoe adjuster by turning the adjusting wheel.


9. REMOVE REAR SPEED SENSOR LH (w/ ABS, VSC)

  1. Disconnect the sensor connector.

    C225638

  1. Detach the clamp.

  1. Remove the 2 bolts and 2 harness clamps.

  1. Remove the bolt and speed sensor LH.

  1. Disconnect the sensor connector.

    C225637

  1. Detach the connector.

  1. Detach the 2 clamps.

  1. Remove the bolt and harness clamp.

  1. Remove the bolt and speed sensor RH.


10. REMOVE FRONT BRAKE SHOE (for 2WD)

  1. C111397E01
    Using SST, remove the shoe hold down spring cup, shoe hold down spring and pin.
    SST
    09718-00010  

  1. Remove the shoe and tension spring.


11. REMOVE REAR BRAKE SHOE (for 2WD)

  1. C111398E01
    Using SST, remove the shoe hold down spring cup, shoe hold down spring and pin.
    SST
    09718-00010  

  1. Using needle-nose pliers, remove the adjust lever tension spring from the automatic adjust lever. Then remove the shoe.

  1. C111480
    Using needle-nose pliers, disconnect the No. 3 parking brake cable from the parking brake shoe lever.


12. REMOVE BRAKE SHOES (for 4WD and Pre-Runner)

C111498
  1. Using pliers, remove the shoe hold down springs, pins, front brake shoe and rear brake shoe.

  1. C113223
    Push the front or rear side of the wheel brake cylinder with the brake shoe. Then remove the side of the brake shoe opposite to the side of the cylinder being pushed. Finally remove the remaining side of the brake shoe.

    NOTICE:
    Be careful not to damage the cylinder dust boot.

  1. C113224
    Move one of the shoes downward and remove the shoe tension spring.

  1. C115339
    Remove the brake shoe front and rear side.

  1. Remove the strut set and return spring from the shoe.

  1. Remove the support clip from the strut set and return spring.

  1. C111502
    Using needle-nose pliers, disconnect the No. 3 parking brake cable from the parking brake shoe lever.


13. DISCONNECT PARKING BRAKE CABLE
  1. Remove the 2 bolts and disconnect the parking brake cable.


14. REMOVE REAR AXLE SHAFT WITH BACKING PLATE

C191121
  1. Remove the 4 nuts.

  1. Pull out the axle shaft from the axle housing.


15. REMOVE O-RING
  1. Remove the O-ring from the axle housing.


16. REMOVE REAR AXLE SHAFT OIL SEAL LH

F050871E02
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the axle housing hole.


17. REMOVE BACKING PLATE TO REAR AXLE HOUSING SETTING BOLT

C190684
  1. Temporarily install 4 nuts to the setting bolts.

    NOTICE:
    Do not use any nuts removed from the vehicle, as they may be damaged.

  1. Using a hammer, tap out the 4 setting bolts from the backing plate.

  1. Remove the 4 nuts and 4 setting bolts.


18. REMOVE REAR AXLE BEARING INNER RETAINER LH AND REAR SKID CONTROL ROTOR (w/ ABS, VSC)

C190685
  1. Grind the retainer and skid control rotor surfaces using a grinder, and then pry them off with a chisel and hammer.

    NOTICE:
    Be careful not to damage the axle shaft.


19. REMOVE REAR AXLE BEARING INNER RETAINER LH

C190686
  1. Using a snap ring expander, remove the snap ring.

  1. C190689
    Grind the retainer surface using a grinder, and then pry it off with a chisel and hammer.

    NOTICE:
    Be careful not to damage the axle shaft.

  1. Remove the shaft washer from the axle shaft.


20. REMOVE REAR AXLE SHAFT LH
  1. Insert the setting bolts into the backing plate and temporarily install washers and nuts to the setting bolts. Tighten the nuts to temporarily install the setting bolts to the backing plate and bearing case.

  1. Remove the nuts and washers from the setting bolts.

  1. C190687E01
    Install SST to the backing plate with the 4 nuts.
    SST
    09521-25011  

  1. C190688E01
    Using SST and a press, press out the axle shaft.

  1. Remove the 4 nuts and SST.

  1. Temporarily install 4 nuts to the setting bolts.

    NOTICE:
    Do not use any nuts removed from the vehicle, as they may be damaged.

  1. Using a hammer, tap out the 4 setting bolts from the backing plate.

  1. Remove the 4 nuts and 4 setting bolts.


21. REMOVE REAR AXLE HUB BOLT LH

  1. C190690E01
    Secure the axle shaft between aluminum plates in a vise.

  1. for 2WD:
    Using SST, remove the 5 hub bolts.

    SST
    09650-17011  

  1. C191008E01
    for 4WD and Pre-Runner:
    Using SST, remove the 6 hub bolts.
    SST
    09650-17011  

  1. Remove the deflector and gasket from the axle shaft.

    NOTICE:
    1. Do not deform the deflector.
    2. Make sure to align the groove of SST with the flange of the oil deflector.


22. INSPECT REAR AXLE SHAFT LH

F050876E01
  1. Using a dial indicator, measure the rear axle shaft shaft runout and flange runout.

    Maximum runout:
    Item
    Specified Condition
    Shaft runout
    1.5 mm (0.0591 in.)
    Flange runout
    0.10 mm (0.00394 in.)

    If the rear axle shaft or flange is damaged or worn, or if the runout is greater than the maximum, replace the rear axle shaft.


23. REMOVE REAR AXLE SHAFT OUTER OIL SEAL

C190691E01
  1. Using SST, tap out the outer oil seal.

    SST
    09308-00010  


24. REMOVE REAR AXLE SHAFT BEARING LH

C190692E01
  1. Using SST and a press, press out the bearing.

    SST
    09223-56010  
    09950-60010   (09951-00640)

← ON-VEHICLE INSPECTION (from Jun 2011)INSTALLATION (Jun 2011 – Jul 2013) →