2014 Hilux · Service Manual BRAKE

ABS Warning Light Remains ON

Circuit diagnosis · Vehicles built Jun 2011 – Jul 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013

DESCRIPTION

When checking for a 2 digit DTC, the ABS warning light may remain on.

WIRING DIAGRAM

F100585E01
F100586E01

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Turn the ignition switch ON.

  1. Check that the ABS warning light illuminates.

  1. Check if the same DTCs are recorded.

    Result 
    Result
    Proceed to
    DTC is not output (when using intelligent tester)
    A
    DTC is not output (when not using intelligent tester)
    B
    DTC is output
    C



B
Go to step 9

C
REPAIR CIRCUIT INDICATED BY OUTPUT DTC
A


2. INSPECT SKID CONTROL ECU CONNECTOR
  1. Check that each ECU connector is properly installed.

    OK:
    Each ECU connector is properly installed.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3. READ VALUE USING INTELLIGENT TESTER (ECU IG POWER VOLTAGE)
  1. Using the Data List, check for proper functioning of the ECU IG power voltage.

    Skid control ECU 
    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    ECU IG Power Voltage
    ECU power supply voltage / TOO LOW / NORMAL / TOO HIGH
    TOO HIGH: more than 14.0 V
    NORMAL: 10 to 14 V
    TOO LOW: Below 10 V
    -
    Result 
    Result
    Proceed to
    Display is NORMAL
    A
    Display is not NORMAL
    B



B
Go to step 15
A


4. CHECK BRAKE ACTUATOR ASSEMBLY (EXI2 VOLTAGE OF SKID CONTROL ECU)

  1. C122186E01
    Measure the voltage of ECU.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S2-22 (EXI2) - Body ground
    Ignition switch ON
    Rear differential lock switch OFF
    8 to 14 V
    S2-22 (EXI2) - Body ground
    Ignition switch ON
    Rear differential lock switch ON
    Below 1.5 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


5. INSPECT TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK)

  1. F052057E03
    Measure the resistance of the switch.

    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    1 - 2
    Not pushed
    10 kΩ or higher



NG
REPLACE TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK)
OK


6. CHECK WIRE HARNESS (TRANSFER INDICATOR SWITCH - SKID CONTROL ECU AND BODY GROUND)
C123166E09
  1. Disconnect the S2 ECU connector.

  1. Disconnect the T31 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    T31-2 -S2-22 (EXI2)
    Below 1 Ω
    T31-2 - Body ground
    10 kΩ or higher
    T31-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


7. CHECK ABS WARNING LIGHT
C108884E08
  1. Disconnect the S2 ECU connector.

  1. Turn the ignition switch ON.

  1. Using a service wire, connect terminal WA to GND1 or GND2 of the S2 ECU connector. Check the ABS warning light.

    OK:
    ABS warning light turns off.

  1. Turn the ignition switch OFF.

  1. Remove the service wire.

  1. Turn the ignition switch ON. Check the ABS warning light.

    OK:
    ABS warning light illuminates.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


8. CHECK WIRE HARNESS (SKID CONTROL ECU - COMBINATION METER ASSEMBLY AND BODY GROUN)
C108898E29
  1. Disconnect the S2 ECU connector.

  1. Disconnect the C25 meter connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    S2-13 (WA) - C25-38
    Below 1 Ω
    S2-13 (WA) - Body ground
    10 kΩ or higher
    S2-2 (GND1) - Body ground
    Below 1 Ω
    S2-24 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY

9. INSPECT SKID CONTROL ECU CONNECTOR
  1. Check that each ECU connector is properly installed.

    OK:
    Each ECU connector is properly installed.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


10. CHECK BRAKE ACTUATOR ASSEMBLY (EXI2 VOLTAGE OF SKID CONTROL ECU)

  1. C122186E01
    Measure the voltage of ECU.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S2-22 (EXI2) - Body ground
    Ignition switch ON
    Rear differential lock switch OFF
    8 to 14 V
    S2-22 (EXI2) - Body ground
    Ignition switch ON
    Rear differential lock switch ON
    Below 1.5 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


11. CHECK TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK)

  1. F052057E03
    Measure the resistance of the switch.

    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Pushed
    Below 1 Ω
    1 - 2
    Not pushed
    10 kΩ or higher



NG
REPLACE TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK)
OK


12. CHECK WIRE HARNESS (TRANSFER INDICATOR SWITCH - SKID CONTROL ECU AND BODY GROUND)
C123166E09
  1. Disconnect the S2 ECU connector.

  1. Disconnect the T31 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    T31-2 -S2-22 (EXI2)
    Below 1 Ω
    T31-2 - Body ground
    10 kΩ or higher
    T31-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


13. CHECK ABS WARNING LIGHT
C108884E10
  1. Disconnect the S2 ECU connector.

  1. Turn the ignition switch ON.

  1. Using a service wire, connect terminal WA to GND1 or GND2 of the S2 ECU connector. Check the ABS warning light.

    OK:
    ABS warning light turns off.

  1. Turn the ignition switch OFF.

  1. Remove the service wire.

  1. Turn the ignition switch ON. Check the ABS warning light.

    OK:
    ABS warning light illuminates.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


14. CHECK WIRE HARNESS (SKID CONTROL ECU - COMBINATION METER AND BODY GROUND)
C108898E29
  1. Disconnect the S2 ECU connector.

  1. Disconnect the C25 meter connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    S2-13 (WA) - C25-38
    Below 1 Ω
    S2-13 (WA) - Body ground
    10 kΩ or higher
    S2-2 (GND1) - Body ground
    Below 1 Ω
    S2-24 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY

15. CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY)
C108884E09
  1. Disconnect the S2 ECU connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    S2-25 (IG1) - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY


← C1337/37 Diameter of the Tire is not Uniform (from Jun 2011)ABS Warning Light Remains ON (from Aug 2013) →