ABS Warning Light Remains ON
Circuit diagnosis · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2013 from Aug 2013
DESCRIPTION
When checking for a 2 digit DTC, the ABS warning light may remain on.WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Turn the ignition switch ON.
Check that the ABS warning light illuminates.
Check if the same DTCs are recorded.
Result Result
Proceed to
DTC is not output (when using intelligent tester)
A
DTC is not output (when not using intelligent tester)
B
DTC is output
C
|
|
||||
|
|
||||
| A | |
| 2. INSPECT SKID CONTROL ECU CONNECTOR |
Check that each ECU connector is properly installed.
- OK:
- Each ECU connector is properly installed.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (ECU IG POWER VOLTAGE) |
Using the Data List, check for proper functioning of the ECU IG power voltage.
Skid control ECU Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
ECU IG Power Voltage
ECU power supply voltage / TOO LOW / NORMAL / TOO HIGH
TOO HIGH: more than 14.0 V
NORMAL: 10 to 14 V
TOO LOW: Below 10 V
-
Result Result
Proceed to
Display is NORMAL
A
Display is not NORMAL
B
|
|
||||
| A | |
| 4. CHECK BRAKE ACTUATOR ASSEMBLY (EXI2 VOLTAGE OF SKID CONTROL ECU) |
Measure the voltage of ECU.

- Standard voltage:
Tester Connection
Condition
Specified Condition
S2-22 (EXI2) - Body ground
Ignition switch ON
Rear differential lock switch OFF
8 to 14 V
S2-22 (EXI2) - Body ground
Ignition switch ON
Rear differential lock switch ON
Below 1.5 V
|
|
||||
| OK | |
| 5. INSPECT TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK) |
Measure the resistance of the switch.

Tester Connection
Condition
Specified Condition
1 - 2
Pushed
Below 1 Ω
1 - 2
Not pushed
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK WIRE HARNESS (TRANSFER INDICATOR SWITCH - SKID CONTROL ECU AND BODY GROUND) |
![]() ![]() |
Disconnect the S2 ECU connector.
Disconnect the T31 switch connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
T31-2 -S2-22 (EXI2)
Below 1 Ω
T31-2 - Body ground
10 kΩ or higher
T31-1 - Body ground
Below 1 Ω
|
|
||||
| OK | |
| 7. CHECK ABS WARNING LIGHT |
![]() ![]() |
Disconnect the S2 ECU connector.
Turn the ignition switch ON.
Using a service wire, connect terminal WA to GND1 or GND2 of the S2 ECU connector. Check the ABS warning light.
- OK:
- ABS warning light turns off.
Turn the ignition switch OFF.
Remove the service wire.
Turn the ignition switch ON. Check the ABS warning light.
- OK:
- ABS warning light illuminates.
|
|
||||
| OK | |
| 8. CHECK WIRE HARNESS (SKID CONTROL ECU - COMBINATION METER ASSEMBLY AND BODY GROUN) |
![]() ![]() |
Disconnect the S2 ECU connector.
Disconnect the C25 meter connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
S2-13 (WA) - C25-38
Below 1 Ω
S2-13 (WA) - Body ground
10 kΩ or higher
S2-2 (GND1) - Body ground
Below 1 Ω
S2-24 (GND2) - Body ground
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 9. INSPECT SKID CONTROL ECU CONNECTOR |
Check that each ECU connector is properly installed.
- OK:
- Each ECU connector is properly installed.
|
|
||||
| OK | |
| 10. CHECK BRAKE ACTUATOR ASSEMBLY (EXI2 VOLTAGE OF SKID CONTROL ECU) |
Measure the voltage of ECU.

- Standard voltage:
Tester Connection
Condition
Specified Condition
S2-22 (EXI2) - Body ground
Ignition switch ON
Rear differential lock switch OFF
8 to 14 V
S2-22 (EXI2) - Body ground
Ignition switch ON
Rear differential lock switch ON
Below 1.5 V
|
|
||||
| OK | |
| 11. CHECK TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK) |
Measure the resistance of the switch.

Tester Connection
Condition
Specified Condition
1 - 2
Pushed
Below 1 Ω
1 - 2
Not pushed
10 kΩ or higher
|
|
||||
| OK | |
| 12. CHECK WIRE HARNESS (TRANSFER INDICATOR SWITCH - SKID CONTROL ECU AND BODY GROUND) |
![]() ![]() |
Disconnect the S2 ECU connector.
Disconnect the T31 switch connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
T31-2 -S2-22 (EXI2)
Below 1 Ω
T31-2 - Body ground
10 kΩ or higher
T31-1 - Body ground
Below 1 Ω
|
|
||||
| OK | |
| 13. CHECK ABS WARNING LIGHT |
![]() ![]() |
Disconnect the S2 ECU connector.
Turn the ignition switch ON.
Using a service wire, connect terminal WA to GND1 or GND2 of the S2 ECU connector. Check the ABS warning light.
- OK:
- ABS warning light turns off.
Turn the ignition switch OFF.
Remove the service wire.
Turn the ignition switch ON. Check the ABS warning light.
- OK:
- ABS warning light illuminates.
|
|
||||
| OK | |
| 14. CHECK WIRE HARNESS (SKID CONTROL ECU - COMBINATION METER AND BODY GROUND) |
![]() ![]() |
Disconnect the S2 ECU connector.
Disconnect the C25 meter connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
S2-13 (WA) - C25-38
Below 1 Ω
S2-13 (WA) - Body ground
10 kΩ or higher
S2-2 (GND1) - Body ground
Below 1 Ω
S2-24 (GND2) - Body ground
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 15. CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY) |
![]() ![]() |
Disconnect the S2 ECU connector.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Condition
Specified Condition
S2-25 (IG1) - Body ground
Ignition switch ON
10 to 14 V
|
|
||||
| OK | ||
| ||





