2014 Hilux · Service Manual BRAKE

C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction

Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

Refer to DTCs C0200/31, C0205/32, C1235/35 and C1236/36.
DTCs C1273/73, C1274/74, C1277/77 and C1278/78 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs C1273/73, C1274/74, C1277/77 and C1278/78 are output only in the test mode.
DTC No.
DTC Detection Condition
Trouble Area
C0210/33
C0215/34
When one of following occurs
  1. With vehicle speed at 10 km/h (6 mph) or more, sensor signal circuit of faulty wheel is open or short for 1 sec. or more
  2. Momentary interruption of sensor signal of faulty wheel has occurred 7 times or more
  3. Sensor signal circuit is open for 0.5 sec. or more
  1. Rear speed sensor
  2. Rear speed sensor circuit
  3. Rear speed sensor rotor
  4. Sensor installation
C1238/38
C1239/39
At vehicle speed of 20 km/h (12 mph) or more, condition that noise is included in speed sensor signal continues for 5 sec. or more.
  1. Rear speed sensor
  2. Rear speed sensor circuit
  3. Sensor installation
C1273/73
Detected only during test mode
  1. Rear speed sensor RH
  2. Sensor installation
  3. Rear speed sensor rotor RH
C1274/74
Detected only during test mode
  1. Rear speed sensor LH
  2. Sensor installation
  3. Rear speed sensor rotor LH
C1277/77
Detected only during test mode
  1. Rear speed sensor rotor RH
C1278/78
Detected only during test mode
  1. Rear speed sensor rotor LH

HINT:
  1. DTCs C0210/33 and C1238/38 are for the rear speed sensor RH.
  2. DTCs C0215/34 and C1239/39 are for the rear speed sensor LH.


WIRING DIAGRAM

C149728E76

INSPECTION PROCEDURE


1. CHOOSE DIAGNOSIS METHOD
  1. Choose the diagnosis method.

    Method 
    Method
    Proceed to
    Using intelligent tester
    A
    Not using intelligent tester
    B



B
Go to step 4
A


2. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
  1. Check the Data List for proper functioning of the rear speed sensor.

    Skid control ECU 
    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Wheel speed sensor (RR)
    reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Speed similar to that of speedometer
    RL Wheel Speed
    Wheel speed sensor (RL)
    reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    Speed similar to that of speedometer

    OK:
    There is almost no difference between actual wheel speed and displayed speed value.

    HINT:
    There is a tolerance of +/-10% in the speedometer indication.



NG
Go to step 4
OK


3. INSPECT SPEED SENSOR AND SENSOR ROTOR SERRATIONS
C108867E02
  1. Connect an oscilloscope to terminals 33 (RR+) and 34 (RR-), and 11 (RL+) and 12 (RL-) of the S2 skid control ECU connector.

  1. Drive the vehicle at about 30 km/h (19 mph), and check the signal waveform.

    OK:
    A waveform is output, as shown in the illustration.

    HINT:
    1. As vehicle speed (wheel revolution speed) increases, the wavelength shortens and the fluctuation in the output voltage becomes greater.
    2. Scratches, looseness or foreign matter on the speed sensor rotor cause noise (errors) in the signal waveform.



NG
Go to step 8
OK

REPLACE BRAKE ACTUATOR ASSEMBLY

4. INSPECT REAR SPEED SENSOR
C225544E03
  1. Disconnect the S40 and S41 rear speed sensor connectors.

  1. Measure the resistance of the speed sensors.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    0.65 to 1.8 kΩ
    1 - Body ground
    10 kΩ or higher
    2 - Body ground
    10 kΩ or higher

    HINT:
    Check the speed sensor signal after the speed sensor replacement.



NG
REPLACE REAR SPEED SENSOR
OK


5. CHECK WIRE HARNESS (SKID CONTROL ECU - REAR SPEED SENSOR)
C225864E05
  1. Disconnect the S2 ECU connector.

  1. Disconnect the S40 and S41 rear speed sensor connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LH:
    Tester Connection
    Specified Condition
    S2-11 (RL+) - S40-2
    Below 1 Ω
    S2-12 (RL-) - S40-1
    Below 1 Ω
    S40-2 - Body ground
    10 kΩ or higher
    S40-1 - Body ground
    10 kΩ or higher
    RH:
    Tester Connection
    Specified Condition
    S2-33 (RR+) - S41-2
    Below 1 Ω
    S2-34 (RR-) - S41-1
    Below 1 Ω
    S41-2 - Body ground
    10 kΩ or higher
    S41-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6. INSPECT SPEED SENSOR AND SENSOR ROTOR SERRATIONS
C108867E02
  1. Connect an oscilloscope to terminals 33 (RR+) and 34 (RR-), and 11 (RL+) and 12 (RL-) of the S2 skid control ECU connector.

  1. Drive the vehicle at about 30 km/h (19 mph), and check the signal waveform.

    OK:
    A waveform is output, as shown in the illustration.

    HINT:
    1. As vehicle speed (wheel revolution speed) increases, the wavelength shortens and the fluctuation in the output voltage becomes greater.
    2. Scratches, looseness or foreign matter on the speed sensor rotor cause noise (errors) in the signal waveform.



NG
Go to step 8
OK


7. CHECK IF DTC OUTPUT RECURS
  1. Clear the DTCs.

  1. Drive the vehicle at approximately 30 km/h (19 mph) or more for 60 seconds or more.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY

8. INSPECT REAR SPEED SENSOR (INSTALLATION)
C108871E08
  1. Check the rear speed sensor installation (Click here).

    OK:
    The installation bolt is tightened properly.
    There is no clearance between the sensor and rear axle housing.

    HINT:
    Check the speed sensor signal after the speed sensor replacement.



NG
SECURELY REINSTALL REAR SPEED SENSOR
OK


9. INSPECT REAR SPEED SENSOR (TIP)
  1. Remove the rear speed sensor.

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on sensor tip.

    HINT:
    1. If the sensor is contaminated with oil or other foreign material, clean the sensor.
    2. If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
    3. Check the speed sensor signal after cleaning or replacing the speed sensor.

    NOTICE:
    Do not replace the speed sensor if no damage to the speed sensor tip is found.



NG
CLEAN OR REPLACE SPEED SENSOR
OK


10. INSPECT SPEED SENSOR ROTOR
  1. Remove the rear axle shaft with backing plate.

  1. Check the sensor rotor serrations.

    OK:
    No scratches, missing teeth or foreign matter on sensor rotor.

    HINT:
    1. If foreign matter is attached, remove it and check the output waveform after reassembly.
    2. Check the speed sensor signal after cleaning or replacing the speed sensor rotor.



NG
CLEAN OR REPLACE SPEED SENSOR ROTOR
OK


11. CHECK IF DTC OUTPUT RECURS
  1. Clear the DTCs.

  1. Drive the vehicle at approximately 30 km/h (19 mph) or more for 60 seconds or more.

  1. Check for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY


← C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction (+ 7 more codes) (Jun 2011 – Jul 2012)C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction (+ 7 more codes) (from Aug 2013) →