2014 Hilux · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Jun 2011

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. INSTALL FRONT DISC

  1. C111369E01
    Align the matchmarks and install the disc.

    HINT:
    When replacing the disc with a new one, select the installation position where the disc has the minimum runout.


2. INSTALL FRONT DISC BRAKE BUSH DUST BOOT

  1. C122649E03
    Apply a light coat of lithium soap base glycol grease to 2 new boots.

  1. Install the 2 boots to the mounting.


3. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

  1. C239762E02
    Apply a light coat of lithium soap base glycol grease to the pins and a new bush as shown in the illustration.

  1. Install the bush to the pin (lower).

  1. Install the 2 pins (upper and lower) to the mounting.


4. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING LH
  1. Install the cylinder mounting with the 2 bolts.

    Torque:
    117 N*m{ 1191 kgf*cm , 86 ft.*lbf }


5. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE
  1. Install the 2 plates to the mounting.


6. INSTALL FRONT ANTI-SQUEAL SHIM KIT

  1. C177135E03
    Install the No. 1 and No. 2 anti-squeal shims to each pad as shown in the illustration.

    NOTICE:
    There should be no oil or grease on the friction surface of the pads and disc.


7. INSTALL FRONT DISC BRAKE PAD
  1. Install the 2 disc brake pads to the mounting.

    NOTICE:
    There should be no oil or grease on the friction surface of the pads and disc.


8. INSTALL DISC BRAKE CYLINDER ASSEMBLY LH

  1. C242453E02
    Apply silicon grease on contact surface of each fingers.

  1. C121983
    Install the cylinder with the 2 bolts.

    Torque:
    29 N*m{ 291 kgf*cm , 21 ft.*lbf }


9. CONNECT FRONT FLEXIBLE HOSE

  1. C121982
    Connect the flexible hose with a new gasket and new union bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    NOTICE:
    Install the flexible hose lock securely in the lock hole in the cylinder.


10. FILL RESERVOIR WITH BRAKE FLUID

Fluid:
SAE J1704 or FMVSS No. 116 DOT 4


11. BLEED AIR FROM BRAKE MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.

    C242461E01

  1. Slowly depress and hold the brake pedal.

  1. Cover the outer holes with your finger, and release the pedal.

    C242462E01

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake lines to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


12. BLEED AIR FROM BRAKE LINE
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    for front brake (2WD):
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for front brake (4WD and Pre-Runner):
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    for rear brake (2WD):
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    for rear brake (4WD and Pre-Runner):
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.


13. BLEED AIR FROM CLUTCH LINE (for Manual Transmission)

C112661E01
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled out of the clutch line.


14. CHECK BRAKE FLUID LEVEL IN RESERVOIR

  1. F052092
    Check the fluid level.
    If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Fluid:
    SAE J1704 or FMVSS No. 116 DOT 4


15. CHECK FOR BRAKE FLUID LEAKAGE

16. INSTALL FRONT WHEEL
  1. Install the front wheel.

    Torque:
    for steel wheel:
    152 N*m{ 1550 kgf*cm , 112 ft.*lbf }
    for aluminum wheel:
    121 N*m{ 1234 kgf*cm , 89 ft.*lbf }

← REASSEMBLY (from Jun 2011)COMPONENTS (from Jun 2011) →