2014 Hilux · Service Manual BRAKE

ADJUSTMENT

Removal / installation · Vehicles built from Jun 2011


1. CHECK PARKING BRAKE LEVER TRAVEL
  1. Pull the parking brake lever to fully engage the parking brake.

  1. Release the lever to disengage the parking brake.

  1. Slowly pull the parking brake lever all the way, and count the number of clicks.

    Standard parking brake lever travel when pulled with a force of 200 N (20 kgf, 45 lbf):
    6 to 8 clicks (for 2WD)
    7 to 9 clicks (for 4WD and Pre-Runner)


2. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY
(Click here)

3. REMOVE REAR WHEEL

4. ADJUST BRAKE SHOE CLEARANCE (for 2WD)

  1. Check that each part is installed properly.

    C115333E01

  1. C111493
    Measure the inside diameter of the drum and diameter of the brake shoes. Check that the difference between the diameters is the correct shoe clearance.

    Standard shoe clearance:
    0.5 mm (0.0197 in.)

    NOTICE:
    There should be no oil or grease on the contact surfaces of the shoe lining and drum.


5. ADJUST BRAKE SHOE CLEARANCE (for 4WD and Pre-Runner)

  1. Check that each part is installed properly.

    C123245E01

  1. C111600
    Measure the inside diameter of the drum and the diameter of the shoes. Check that the difference between the diameters is the correct shoe clearance.

    Standard shoe clearance:
    0.6 mm (0.0236 in.)

    NOTICE:
    There should be no oil or grease on the contact surfaces of the shoe lining and drum.


6. ADJUST PARKING BRAKE LEVER TRAVEL
  1. Completely release the parking brake lever.

  1. C237675E01
    Loosen the lock nut.
    Text in Illustration 
    *1
    Lock Nut
    *2
    No. 1 Parking Brake Cable Adjusting Nut

  1. Turn the No. 1 parking brake cable adjusting nut until the lever travel is correct.

  1. Tighten the lock nut.

    Torque:
    5.2 N*m{ 53 kgf*cm , 46 in.*lbf }

    HINT:
    If the lever travel cannot be fully adjusted with this procedure, proceed to the Adjust Parking Brake Turn Buckle procedure.


7. ADJUST PARKING BRAKE TURN BUCKLE

  1. C237676E01
    Loosen the lock nut and turn the buckle until the lever travel is correct.
    Text in Illustration 
    *1
    Lock Nut
    *2
    Turn Buckle

  1. Tighten the lock nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


8. INSPECT BRAKE WARNING LIGHT
  1. Operate the parking brake lever and check the illumination condition of the brake warning light.

    OK:
    The brake warning light always illuminates at the first click.


9. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
(Click here)

10. INSTALL REAR WHEEL (for 2WD)
  1. Install the wheel.

    Torque:
    152 N*m{ 1,550 kgf*cm , 112 ft.*lbf } for steel wheel
    121 N*m{ 1,234 kgf*cm , 89 ft.*lbf } for aluminum wheel


11. INSTALL REAR WHEEL (for 4WD and Pre-Runner)
  1. Install the wheel.

    Torque:
    105 N*m{ 1,070 kgf*cm , 77 ft.*lbf }

← PROBLEM SYMPTOMS TABLE (from Aug 2013)COMPONENTS (from Jun 2011) →