2014 Hilux · Service Manual DRIVE LINE

INSTALLATION

Removal / installation · Vehicles built from Jun 2011


1. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY

  1. C237477
    Install the front No. 3 differential support with the 2 bolts.

    Torque:
    108 N*m{ 1100 kgf*cm , 80 ft.*lbf }

  1. C237476
    Install the front No. 2 mounting support with the 2 bolts.

    Torque:
    160 N*m{ 1632 kgf*cm , 118 ft.*lbf }

  1. C237475
    Install the front No. 1 mounting support with the 3 bolts.

    Torque:
    186 N*m{ 1899 kgf*cm , 137 ft.*lbf }

  1. Support the front differential with a jack.

  1. C237474E01
    Install the 2 front mounting bolts and 2 nuts.
    Text in Illustration 
    *1
    Mounting Bolt
    *2
    Mounting Nut

    Torque:
    137 N*m{ 1400 kgf*cm , 101 ft.*lbf }

  1. Install the front No. 1 differential mounting nut.

    Torque:
    87 N*m{ 889 kgf*cm , 64 ft.*lbf }

  1. Install the front differential breather tube bracket with the bolt.

    Torque:
    13 N*m{ 131 kgf*cm , 9 ft.*lbf }

  1. Lower the jack.


2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
(Click here)

3. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


4. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
  1. for TSAM Made:
    (Click here)

  1. for TMT Made:
    (Click here)


5. ADD DIFFERENTIAL OIL

  1. D025304E51
    Add differential oil so that the oil level is within 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.
    Text in Illustration 
    *a
    0 to 5 mm (0 to 0.196 in.)

    NOTICE:
    1. After changing the oil seal, drive the vehicle and then check the oil level again.
    2. Too much or too little oil will lead to differential problems.

    HINT:
    If necessary, fill the differential carrier assembly with hypoid gear oil.

    Recommended viscosity:
    Item
    Temperature
    Viscosity
    Front differential (w/ A.D.D.)
    SAE 75W-90
    Front differential (w/o A.D.D.)
    Rear differential
    Above -18°C (0°F)
    SAE 90
    Below -18°C (0°F)
    SAE 80W-90 or SAE 80W

    Differential oil type:
    Item
    Oil type
    Front differential
    Rear differential
    Hypoid gear oil API GL-5 or equivalent
    Rear differential (for LSD)
    Hypoid gear oil LSD API GL-5 or equivalent

    Standard front differential oil capacity:
    Item
    Capacity
    w/o A.D.D.
    1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
    w/ A.D.D.
    1.60 to 1.70 liters (1.69 to 1.79 US qts., 1.41 to 1.49 Imp. qts.)

    TMT made Standard rear differential oil capacity:
    Item
    Capacity
    2WD and w/ LSD
    3.15 to 3.25 liters (3.33 to 3.43 US qts., 2.78 to 2.86 Imp. qts.)
    4WD and w/o LSD
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)

    TSAM made :
    Item
    Capacity
    2WD and made for DANA
    2.30 to 2.40 liters (2.43 to 2.54 US qts., 2.02 to 2.11 Imp. qts.)
    4WD, Pre-runner and made for DANA
    (w/o LSD, A.D.D.)
    2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)
    w/ LSD for 2WD
    3.15 to 3.25 liters (3.33 to 3.43 US qts., 2.78 to 2.86 Imp. qts.)
    w/ LSD for 4WD
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
    w/ Differential lock
    2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.)

  1. Check for oil leakage when the oil level is low.

  1. for front differential:

    1. A272243E01
      Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.
      SST
      09961-00950  
      Text in Illustration 
      *1
      10 mm Straight Hexagon Wrench
      *2
      10 mm Union Nut Wrench
      *3
      Socket Adaptor

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

      NOTICE:
      1. Make sure all the tools are connected in a straight line.
      2. Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

        Formula:
        T' = T x L3 / (L1 + L2 + L3)
        - T' = Spec. value of torque wrench
        - T = Value of specified tightening torque
        - L1 = Length of union nut wrench
        - L2 = Length of SST
        - L3 = Length of torque wrench

  1. for rear differential:

    1. Install a new gasket and the differential filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }


6. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }


7. INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }

← REASSEMBLY (from Jun 2011)COMPONENTS (from Jun 2011) →