2014 Hilux · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. INSPECT DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

  1. C237478E01
    Using SST and a dial indicator, measure the ring gear backlash.
    SST
    09564-33010  

    Backlash:
    0.11 to 0.21 mm (0.00433 to 0.00826 in.)

    1. If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.

      HINT:
      Perform the measurement at 3 or more positions around the circumference of the ring gear.


2. INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

  1. C236648E01
    Using a dial indicator, measure the runout of the companion flange vertically and laterally.
    Text in Illustration 
    *a
    30 mm (1.18 in.)

    Maximum Runout:
    Item
    Specified Condition
    Vertical runout
    0.10 mm (0.00394 in.)
    Lateral runout
    0.10 mm (0.00394 in.)

    1. If the runout is more than the maximum, replace the companion flange.


3. REMOVE DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY

  1. C237694
    Remove the 4 bolts.

  1. Using a hammer, pry out the actuator from the differential tube.


4. REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY

  1. C237479
    Remove the 4 bolts.

  1. Using a plastic-faced hammer, tap out the differential tube.


5. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL LH

  1. C237480E01
    Using SST, tap out the oil seal.
    SST
    09308-00010  


6. REMOVE DIFFERENTIAL CLUTCH SLEEVE
  1. Remove the differential clutch sleeve.


7. REMOVE DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY
  1. Remove the snap ring from the inter shaft.

  1. C237671E01
    Using SST, remove the inter shaft.
    SST
    09350-20015   (09369-20040)
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)
    Text in Illustration 
    *a
    Turn
    *b
    Hold


8. REMOVE FRONT DIFFERENTIAL SIDE BEARING RETAINER DEFLECTOR

  1. C237481E01
    Using a screwdriver, pry out the bearing retainer deflector.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.


9. REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT

  1. C236628E01
    Using SST and a hammer, loosen the staked part of the nut.
    SST
    09930-00010   (09931-00010, 09931-00020)

  1. C236629E01
    Using SST to hold the companion flange, remove the nut.
    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold


10. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

  1. C236630E01
    Using SST, remove the companion flange with dust deflector.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.


11. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL

  1. C236631E01
    Using SST, remove the oil seal.
    SST
    09308-10010  
    Text in Illustration 
    *1
    Oil Seal
    *2
    Oil Slinger


12. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

  1. C237315
    Remove the oil slinger from the drive pinion.


13. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C237691E01
    Using SST, remove the roller bearing (inner) from the drive pinion.
    SST
    09556-22010  


14. REMOVE DIFFERENTIAL SIDE BEARING RETAINER
  1. Remove the 10 bolts and tap out the retainer with a plastic-faced hammer.


15. REMOVE DIFFERENTIAL CASE ASSEMBLY

16. REMOVE DIFFERENTIAL DRIVE PINION

17. REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

  1. C237692
    Remove the bearing spacer from the drive pinion.


18. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C237482E01
    Using SST and a press, press out the roller bearing (inner) and drive pinion plate washer from the drive pinion.
    SST
    09950-00020  

    NOTICE:
    Do not drop the drive pinion.

    HINT:
    If the drive pinion or ring gear is damaged, replace them as a set.


19. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C237483
    Using a brass bar and hammer, tap out the roller bearing (outer).


20. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C237484E01
    Using SST, remove the roller bearing (outer).
    SST
    09502-12010  
    09612-65014   (09612-01020, 09612-01050)
    Text in Illustration 
    *a
    Turn
    *b
    Hold


21. REMOVE FRONT DIFFERENTIAL OIL STORAGE RING
  1. Using a brass bar and hammer, tap out the oil storage ring.


22. REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:
  1. Measure the thickness of the case washer.
  2. Tag the bearing outer races so that they can be reinstalled in the correct locations.

  1. C237485E01
    Using SST and a press, press out the case bearing (outer) and plate washer from the bearing retainer.
    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)
    1. If the bearing is damaged during removal, replace it.

  1. C237486E01
    Using SST and a press, press out the case bearing (outer) and plate washer from the differential carrier.
    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)
    1. If the bearing is damaged during removal, replace it.


23. REMOVE DIFFERENTIAL RING GEAR

  1. C236663E01
    Place matchmarks on the ring gear and differential case.
    Text in Illustration 
    *1
    Matchmark

  1. Remove the 10 ring gear set bolts.

  1. C236664
    Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


24. REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:
The differential case and case bearings should only be removed when replacement is necessary.

  1. C237488E01
    Using SST, remove the 2 case bearings (inner) from the differential case.
    SST
    09950-60010   (09951-00480)
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09953-04020, 09958-04011)
    Text in Illustration 
    *a
    Notch
    *b
    Turn
    *c
    Hold

    HINT:
    Attach the claws of SST to the notch in the differential case assembly to secure SST.


25. DISASSEMBLE DIFFERENTIAL CASE

  1. C236667
    Using a chisel and hammer, unstake the differential case.

  1. C238726
    Using a pin punch and hammer, tap out the straight pin.

  1. C236669
    Remove the following parts from the differential case.

    1. C236670E01
      (1) Differential pinion gear (2 pieces)
    2. (2) Differential pinion gear thrust washer (2 pieces)
    3. (3) Differential pinion shaft
    4. (4) Differential side gear (2 pieces)
    5. (5) Differential side gear thrust washer (2 pieces)


26. INSPECT DIFFERENTIAL GEAR KIT
  1. Check that the differential pinion and differential side gear are not damaged.

    1. If the differential pinion or differential side gear is damaged, replace the differential gear kit.


27. INSPECT FRONT DIFFERENTIAL CASE
  1. Check that the differential case is not damaged.

    1. If the differential case is damaged, replace it.


28. REMOVE FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING

  1. C237523
    Using a brass bar and hammer, tap out the 2 bearings.


29. REMOVE DIFFERENTIAL CLUTCH HUB

  1. C237524
    Using a snap ring expander, remove the snap ring.

  1. Remove the differential clutch hub.


30. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL RH

  1. C237489E01
    Using SST, tap out the oil seal from the differential tube.
    SST
    09308-00010  


31. REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH

  1. C237490
    Using a snap ring expander, remove the snap ring.

  1. Remove the shaft from the differential tube.


32. REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING
  1. Using a snap ring expander, remove the snap ring.

  1. C237491E01
    Using SST, a brass bar and a press, press out the shaft RH bearing.
    SST
    09950-00020  

    NOTICE:
    1. Do not damage the bearing.
    2. Do not drop the shaft.


33. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL CLUTCH HUB

  1. C237525
    Check that there is no wear or damage on the clutch hub and clutch sleeve.
    1. If necessary, replace them.

  1. Check that the clutch sleeve slides smoothly on the clutch hub.


34. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL SIDE GEAR INTER SHAFT

  1. C237646
    Check that there is no wear or damage on the clutch sleeve and side gear inter shaft.
    If necessary, replace clutch sleeve and side gear inter shaft.

  1. Check that clutch sleeve slides smoothly on the side gear inter shaft.


35. INSPECT DIFFERENTIAL CLUTCH SLEEVE AND CLUTCH SLEEVE FORK CLEARANCE

  1. C237647
    Using a feeler gauge, measure the clearance between the sleeve fork and clutch sleeve.

    Maximum clearance:
    0.35 mm (0.0138 in.)

    1. If the clearance is more than the maximum, replace the fork or clutch sleeve.

← REMOVAL (from Jun 2011)REASSEMBLY (from Jun 2011) →