2014 Hilux · Service Manual DRIVE LINE

REASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. ASSEMBLE DIFFERENTIAL CASE

  1. C237345
    Install the side gear thrust washer to the side gear.

  1. Install the 4 rear differential pinion gear thrust washers to the 4 rear drive pinion gears.

  1. Install the 4 rear differential pinion gear thrust washers and 4 rear drive pinion gears to the spider.

  1. Secure the differential case RH.

  1. C237346
    Install the rear differential side gear and rear differential spider to the differential case RH.

  1. C237347
    Using a dial indicator, measure the differential case RH backlash while holding the pinion toward the case.

    Standard backlash:
    0.05 to 0.20 mm (0.00197 to 0.00787 in.)

  1. Remove the rear differential spider from the differential case RH.

  1. C237348
    Install the rear differential side gear and rear differential spider to the differential case LH.

  1. Using a dial indicator, measure the differential case LH backlash while holding the pinion toward the case.

    Standard backlash:
    0.05 to 0.20 mm (0.00197 to 0.00787 in.)

    HINT:
    Using the table below, select 2 thrust washers which will ensure that the backlash is within the specifications.

    Standard Washer Thickness:
    Thickness mm (in.)
    Thickness mm (in.)
    0.88 to 0.92 (0.0347 to 0.0362)
    1.18 to 1.22 (0.0465 to 0.0480)
    0.98 to 1.02 (0.0386 to 0.0401)
    1.28 to 1.32 (0.0504 to 0.0519)
    1.08 to 1.12 (0.0426 to 0.0440)
    -

  1. C237349E01
    Align the matchmarks and assemble the RH and LH cases.
    Text in Illustration 
    *1
    Matchmark

  1. Using a plastic-faced hammer, install the differential case.

  1. Install the 8 bolts.

    Torque:
    54 N*m{ 547 kgf*cm , 40 ft.*lbf }

  1. Install the rear differential lock sleeve to the differential case LH.


2. INSTALL DIFFERENTIAL RING GEAR
  1. Clean the contact surfaces of the differential case and ring gear.

  1. Heat the ring gear in boiling water that is approximately 100°C (212°F).

  1. Carefully remove the ring gear from the boiling water.

  1. C236674E01
    After the moisture on the ring gear has completely evaporated, quickly align the matchmarks on the ring gear and differential case and install the ring gear to the differential case.
    Text in Illustration 
    *1
    Matchmark

  1. Temporarily install 5 new lock plates and the 10 bolts.

  1. After the ring gear cools down, diametrically tighten the 10 bolts uniformly in several passes.

    Torque:
    87 N*m{ 891 kgf*cm , 64 ft.*lbf }

  1. C236675E01
    Using a chisel and hammer, stake the 5 lock plates.

    HINT:
    Strike the tab labeled A so that it is flush with the flat surface of the bolt. Strike the tab labeled B so that half of the tab contacts the bolt as shown in the illustration.


3. INSTALL REAR DIFFERENTIAL CASE BEARING

  1. C237670E01
    Using SST and a press, press the bearing onto the differential case.
    SST
    09950-60010   (09951-00430, 09951-00470, 09951-00480, 09951-00550)
    09950-70010   (09951-00560, 09951-00570, 09951-07150)
    Text in Illustration 
    *A
    for LSD
    *B
    2 Pinion Type


4. INSPECT DIFFERENTIAL RING GEAR RUNOUT
  1. Install the differential case on the carrier, and install the 2 adjusting nuts so that there is no play in the bearing.

  1. Install the 2 bearing caps with the 4 bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }

  1. C236649
    Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

  1. Remove the 2 bearing caps, 2 adjusting nuts and differential case.


5. INSTALL DIFFERENTIAL OIL STORAGE RING
  1. Using a brass bar and hammer, tap in a new oil storage ring.

    NOTICE:
    Be careful not to damage the oil storage ring.


6. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C236677E01
    Using SST and a press, press the bearing (outer) into the carrier.
    SST
    09316-60011   (09316-00011, 09316-00021)


7. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C236678E01
    Using SST and a press, press the bearing (outer) into the carrier.
    SST
    09316-60011   (09316-00011, 09316-00041)


8. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING
  1. Install the plate washer to the drive pinion.

    HINT:
    First, install a washer that has the same thickness as the removed washer. After checking the tooth contact pattern, replace the washer with one of a different thickness if necessary.

  1. C236679E01
    Using SST and a press, press the bearing (inner) onto the drive pinion.
    SST
    09506-30012  


9. ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

  1. C237303
    Install the drive pinion, rear drive pinion tapered roller bearing and rear differential drive pinion oil slinger.

    HINT:
    Install the spacer and oil seal after adjusting the gear contact pattern.

  1. C237304E01
    Using SST, install the companion flange.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. C237305E01
    Adjust the drive pinion preload by tightening the companion flange nut.

  1. Using SST to hold the companion flange in place, tighten the nut.

    SST
    09330-00021   (09330-00030)

    Torque:
    370 N*m{ 3773 kgf*cm , 273 ft.*lbf } or less

    NOTICE:
    1. As there is no spacer, tighten a little at a time. Be careful not to overtighten the nut.
    2. Apply hypoid gear oil LSD to drive pinion thread and nut seat face.

  1. Using a torque wrench, measure the preload.

    Standard Drive Pinion Preload (Starting Torque):
    Bearing
    Preload
    New bearing
    1.0 to 1.5 N*m (11 to 15 kgf*cm, 9 to 13 in.*lbf)
    Reused bearing
    0.5 to 0.7 N*m (6 to 7 kgf*cm, 5 to 6 in.*lbf)

    NOTICE:
    1. For a more accurate measurement, rotate the bearing forward and backward several times before measuring.
    2. Record the differential drive pinion preload for the total preload measurement.


10. INSTALL DIFFERENTIAL CASE ASSEMBLY

  1. C237353
    Apply MP grease to the rack of the shift fork and connecting part of the indicator switch.
    Text in Illustration 
    V100135
    MP grease

  1. Insert the shift fork into the differential carrier as shown in the illustration.

  1. C237354
    Place the outer race and adjusting nut on the left side of the sleeve.

    HINT:
    Check that the sleeve moves smoothly.

  1. C237333
    Insert the shift fork into the groove of the sleeve while holding the sleeve by hand, and install the case to the carrier.

    HINT:
    Make sure that there is backlash between the ring gear and drive pinion.


11. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT

  1. C237355
    Install the 2 adjusting nuts to the carrier, making sure the nuts are threaded properly.


12. INSPECT AND ADJUST DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH

  1. C237332E01
    Align the matchmarks on the cap and carrier.
    Text in Illustration 
    *1
    Matchmark

  1. C238708
    Install the right and left bearing caps with the 4 bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }

    1. If the bearing cap does not fit tightly on the carrier, the adjusting nuts are not threaded properly.

      HINT:
      Reinstall the adjusting nuts if necessary.

  1. C237309E01
    Loosen the 4 bearing cap bolts to the point where the adjusting nuts can be turned by SST.
    Text in Illustration 
    *a
    for LH Side
    *b
    for RH Side

  1. Using SST, tighten the adjusting nut on the ring gear side until the ring gear has a backlash of about 0.2 mm (0.00787 in.).

    SST
    09504-00011  
    09960-10010   (09962-01000, 09963-00700)

  1. While turning the ring gear, use SST to tighten the adjusting nut on the drive pinion side. After the bearings have settled, loosen the adjusting nut on the drive pinion side.

    SST
    09504-00011  
    09960-10010   (09962-01000, 09963-00700)

  1. Using SST, tighten the adjusting nut 1 to 1.5 notches from the 0 preload position.

  1. C237324
    Using a dial indicator, adjust the ring gear backlash until it is within the specification.

    Standard backlash:
    0.13 to 0.18 mm (0.00512 to 0.00708 in.)

    HINT:
    1. The backlash is adjusted by turning the left and right adjusting nuts by an equal amount. For example, loosen the nut on the right side one notch and loosen the nut on the left side one notch.
    2. Perform the measurement at 3 or more positions around the circumference of the ring gear.

  1. C237332
    Tighten the bearing cap bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }


13. INSPECT TOTAL PRELOAD

  1. C237317
    Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    Standard Total Preload:
    Item
    Specified Condition
    New bearing
    0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload
    Reused bearing
    0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload

    If necessary, disassemble and inspect the differential.

    NOTICE:
    Record the differential ring gear preload.


14. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

C237311
  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.

  1. Hold the companion flange firmly in place and rotate the ring gear in both directions.

  1. Inspect the tooth contact pattern.

    1. C178076E02

    2. C237312E01
      If the teeth are not contacting properly, use the following chart to select a proper washer.
      Text in Illustration 
      *1
      Plate Washer

      Standard Plate Washer Thickness:
      Thickness mm (in.)
      Thickness mm (in.)
      1.69 to 1.71 (0.0666 to 0.0673)
      2.02 to 2.04 (0.0796 to 0.0803)
      1.72 to 1.74 (0.0678 to 0.0685)
      2.05 to 2.07 (0.0807 to 0.0814)
      1.75 to 1.77 (0.0689 to 0.0696)
      2.08 to 2.10 (0.0819 to 0.0826)
      1.78 to 1.80 (0.0701 to 0.0708)
      2.11 to 2.13 (0.0831 to 0.0838)
      1.81 to 1.83 (0.0713 to 0.0720)
      2.14 to 2.16 (0.0843 to 0.0850)
      1.84 to 1.86 (0.0725 to 0.0732)
      2.17 to 2.19 (0.0855 to 0.0862)
      1.87 to 1.89 (0.0737 to 0.0744)
      2.20 to 2.22 (0.0867 to 0.0874)
      1.90 to 1.92 (0.0748 to 0.0755)
      2.23 to 2.25 (0.0878 to 0.0885)
      1.93 to 1.95 (0.0760 to 0.0767)
      2.26 to 2.28 (0.0890 to 0.0897)
      1.96 to 1.98 (0.0772 to 0.0779)
      2.29 to 2.31 (0.0902 to 0.0909)
      1.99 to 2.01 (0.0784 to 0.0791)
      2.32 to 2.34 (0.0914 to 0.0921)


15. REMOVE REAR DRIVE PINION NUT

  1. C236628E01
    Using SST and a hammer, loosen the staked part of the nut.
    SST
    09930-00010   (09931-00010, 09931-00020)

  1. C236629E01
    Using SST to hold the companion flange in place, remove the nut.
    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold


16. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

  1. C238724
    Using SST, remove the companion flange with dust deflector.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.


17. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

  1. C237315
    Remove the oil slinger from the drive pinion.


18. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C236632E01
    Using SST, remove the roller bearing (inner).
    SST
    09556-22010  

  1. C236633E01
    Using SST, tap out the roller bearing (outer).
    SST
    09308-00010  


19. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

  1. C237515
    Remove the bearing spacer from the drive pinion.


20. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C237314
    Install the bearing (inner) to the drive pinion.


21. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

  1. C237315
    Install the oil slinger to the drive pinion.


22. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

  1. C236636E01
    Using SST and a hammer, tap in a new oil seal.
    SST
    09554-30011  
    Text in Illustration 
    *a
    Oil Seal Depth

    Standard oil seal depth:
    0 +/-0.3mm (0 +/-0.0118in.)

  1. Apply MP grease to the lip of the oil seal.


23. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

  1. C238725
    Using SST, install the companion flange with dust deflector.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. Apply hypoid gear oil LSD to drive pinion thread and nut seat face.

  1. C237316E01
    Using SST to hold the companion flange in place, install a new nut.
    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    Torque:
    370 N*m{ 3773 kgf*cm , 273 ft.*lbf } or less


24. INSPECT TOTAL PRELOAD

  1. C237317
    Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    Standard Total Preload:
    Bearing
    Preload
    New bearing
    1.1 to 1.6 N*m (12 to 16 kgf*cm, 10 to 14 in.*lbf) + ring gear preload
    Reused bearing
    0.6 to 0.8 N*m (7 to 8 kgf*cm, 6 to 7 in.*lbf) + ring gear preload

    1. If necessary, disassemble and inspect the differential.


25. INSPECT DIFFERENTIAL RING GEAR BACKLASH

  1. C237324
    Using a dial indicator, measure the backlash of the ring gear.

    Standard backlash:
    0.13 to 0.18 mm (0.00512 to 0.00708 in.)

    1. If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

      HINT:
      Perform the measurement at 3 or more positions around the circumference of the ring gear.


26. INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

  1. C236648E01
    Using a dial indicator, measure the runout of the companion flange vertically and laterally.
    Text in Illustration 
    *a
    30 mm (1.18 in.)

    Maximum Runout:
    Runout
    Maximum
    Vertical runout
    0.10 mm (0.00394 in.)
    Lateral runout
    0.10 mm (0.00394 in.)

    1. If the runout is more than the maximum, replace the companion flange.


27. STAKE DRIVE PINION NUT

  1. C236640
    Using a chisel and hammer, stake the nut.


28. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

  1. C237318
    Install 2 new adjusting nut locks to the bearing caps with the 2 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Bend the nut locks.


29. INSTALL REAR DIFFERENTIAL LOCK SHIFT FORK SHAFT

  1. C237358E01
    Apply MP grease to the outer circuit of the fork shaft.
    Text in Illustration 
    *1
    Groove
    *2
    Hole

  1. Install the fork shaft so that the hole of the shift fork aligns with that of the shift fork shaft.

  1. C237359E01
    Remove any seal packing material.
    Text in Illustration 
    *1
    Seal packing

    NOTICE:
    Be careful not to drop oil on the contact surface of the differential carrier and shaft retainer.

  1. Apply seal packing to the carrier as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    HINT:
    Install the shaft retainer within 3 minutes after applying seal packing.

  1. C237360
    Clean the threads of the bolts and retainer bolts holes with toluene or trichloroethylene.

  1. Apply adhesive to 2 or 3 threads at the end of the mounting bolt.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Tighten the shaft retainer with the 2 bolts.

    Torque:
    23 N*m{ 237 kgf*cm , 17 ft.*lbf }

  1. C237361
    Using a 5 mm pin punch and hammer, tap in the slotted spring pin to the shift fork.

  1. C237362E01
    Shift the fork to the lock side.
    Text in Illustration 
    *1
    Lock

  1. C237466E01
    Install the steel ball, spring and spring seat.
    Text in Illustration 
    *1
    Steel Ball
    *2
    Spring
    *3
    Spring Seat
    *4
    Screw Plug

  1. Clean the threads of the 2 plug holes with toluene or trichloroethylene.

  1. Apply adhesive to the plug threads.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using a 6 mm hexagon wrench, install the screw plugs.

    Torque:
    23 N*m{ 237 kgf*cm , 17 ft.*lbf }


30. INSPECT REAR DIFFERENTIAL LOCK SLEEVE

C237467
  1. Measure the distance between the sleeve and tip of the differential case when the differential is free, and when it is locked.

    Standard Distance:
    Position
    Specified Condition
    Lock
    17.44 to 18.86 mm (0.6866 to 0.7425 in.)
    Free
    32.40 to 33.90 mm (1.2756 to 1.3346 in.)


31. INSTALL NO. 4 TRANSFER INDICATOR SWITCH

  1. C121512E03
    Install the indicator switch and a new gasket.
    Text in Illustration 
    *1
    Gasket
    *1
    Switch

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }

  1. Connect the connector.


32. INSTALL DIFFERENTIAL LOCK SHIFT ACTUATOR
  1. Install a new O-ring to the actuator.

  1. Install the actuator to the differential carrier.

    Torque:
    27 N*m{ 270 kgf*cm , 20 ft.*lbf }

  1. C237468E01
    Check that the outermost rack tooth of the shift fork is almost directly above the center line of the actuator installation hole.
    Text in Illustration 
    *1
    Shift Fork
    *2
    Actuator Installation Hole
    V100135
    Outside

  1. C237469E01
    Check that the matchmarks on the pinion of the actuator are in the range between 2 and 8° clockwise of the center line of the actuator.
    Text in Illustration 
    *1
    Matchmark
    *a
    8°
    *b
    108°
    *c
    1.5 V

    NOTICE:
    1. If the matchmarks are not within the specified range, use dry cell batteries to rotate the pinion until the matchmarks are within the range.
    2. Do not apply positive (+) battery voltage directly between terminals.
    3. If the matchmarks come to the limit of the rotation range, do not apply any more voltage.

  1. Install a new O-ring to the actuator.

  1. Apply a light coat of gear oil to the O-ring.

  1. Apply MP grease to the gear parts.

  1. C237470E01
    Check that the outermost rack tooth of the shift fork aligns with the matchmarks on the pinion of the actuator.
    Text in Illustration 
    *1
    Knock Pin

  1. Install the actuator so that the long hole in the actuator fits with the knock pin on the carrier.

    HINT:
    Do not damage the O-ring of the actuator.

  1. Rotate the actuator counterclockwise so that the knock pin slides to the end of the hole as shown in the illustration.

  1. Install the bolt.

    Torque:
    27 N*m{ 270 kgf*cm , 20 ft.*lbf }

← DISASSEMBLY (from Jun 2011)INSTALLATION (from Jun 2011) →