2014 Hilux · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY

  1. C236647
    Secure the differential carrier.


2. INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

  1. C236648E01
    Using a dial indicator, measure the runout of the companion flange vertically and laterally.
    Text in Illustration 
    *a
    30 mm (1.18 in.)

    Maximum Runout:
    Runout
    Maximum
    Vertical runout
    0.10 mm (0.00394 in.)
    Lateral runout
    0.10 mm (0.00394 in.)

    1. If the runout is more than the maximum, replace the companion flange.


3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

  1. C237323
    Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.00276 in.)

    1. If the runout is more than the maximum, replace the ring gear with a new one.


4. INSPECT DIFFERENTIAL RING GEAR BACKLASH

  1. C237324
    Using a dial indicator, measure the backlash of the ring gear.

    Standard backlash:
    0.13 to 0.18 mm (0.00512 to 0.00708 in.)

    1. If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

      HINT:
      Perform the measurement at 3 or more positions around the circumference of the ring gear.


5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

  1. C236639
    Using a torque wrench, measure the preload.

    Standard Preload (Starting Torque):
    Item
    Specified Condition
    New bearing
    1.1 to 1.6 N*m (12 to 16 kgf*cm, 10 to 14 in.*lbf)
    Reused bearing
    0.6 to 0.8 N*m (7 to 8 kgf*cm, 6 to 7 in.*lbf)

    1. If the result is not as specified, adjust the preload.


6. INSPECT TOTAL PRELOAD

  1. C236639
    Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard Total Preload:
    Bearing
    Specified Condition
    New bearing
    0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload
    Reused bearing
    0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload

    If the result is not as specified, adjust the preload.


7. REMOVE DIFFERENTIAL LOCK SHIFT ACTUATOR

  1. C238740
    Remove the 2 bolts and rear differential lock actuator protector.

  1. Remove the differential breather bracket.

  1. C237326
    Remove the bolt and actuator from the differential carrier.

  1. Remove the O-ring.


8. REMOVE NO. 4 TRANSFER INDICATOR SWITCH

  1. C237327E01
    Remove the switch and gasket.
    Text in Illustration 
    *1
    Gasket
    *2
    Switch


9. REMOVE REAR DIFFERENTIAL LOCK SHIFT FORK SHAFT

C237328E01
Text in Illustration 
*1
Steel Ball
*2
Spring Seat
*3
Spring
*4
Screw Plug
  1. Using a 6 mm hexagon wrench, remove the 2 screw plugs.

  1. Remove the spring seat, spring and steel ball.

  1. C237329E01
    Using a 5 mm pin punch and hammer, tap out the slotted spring pin from the shift fork shaft.
    Text in Illustration 
    *1
    Shift Fork Shaft
    *2
    Pin Punch
    *3
    Slotted Spring Pin

  1. C237330
    Remove the 2 bolts from the shaft retainer.

  1. Using a plastic-faced hammer, tap on the retainer to separate it from the differential case.

  1. Remove the shift fork shaft.


10. REMOVE REAR DRIVE PINION NUT

  1. C236628E01
    Using SST and a hammer, loosen the staked part of the nut.
    SST
    09930-00010   (09931-00010, 09931-00020)

  1. C236629E01
    Using SST to hold the companion flange in place, remove the nut.
    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold


11. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

  1. C238724
    Using SST, remove the companion flange with dust deflector.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.


12. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

  1. C236631E01
    Using SST, remove the oil seal.
    SST
    09308-10010  
    Text in Illustration 
    *1
    Oil Seal
    *2
    Oil Slinger


13. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

  1. C237315
    Remove the oil slinger from the drive pinion.


14. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C236655E02
    Using SST, remove the roller bearing (inner) from the drive pinion.
    SST
    09556-22010  
    Text in Illustration 
    *a
    Turn
    *b
    Hold


15. REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

  1. C237331
    Remove the 2 bolts and 2 adjusting nut locks.


16. REMOVE DIFFERENTIAL CASE ASSEMBLY

  1. C237332E01
    Place matchmarks on the bearing cap and differential carrier.
    Text in Illustration 
    *1
    Matchmark

  1. Remove the 4 bolts and 2 differential bearing caps.

  1. Remove the 2 adjusting nuts.

  1. C237333
    Remove the rear differential case assembly from the differential carrier.

    HINT:
    Tag the 2 rear differential case bearings (outer) so that they can be reinstalled in the correct locations.


17. REMOVE DIFFERENTIAL DRIVE PINION
  1. Remove the drive pinion and bearing spacer from the differential carrier.


18. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C238710E01
    Using SST, remove the roller bearing (outer) from the carrier.
    SST
    09308-00010  


19. REMOVE DIFFERENTIAL OIL STORAGE RING

  1. C238707
    Using a brass bar and hammer, tap out the oil storage ring from the carrier.


20. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

  1. C237515
    Remove the bearing spacer from the drive pinion.


21. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C237336
    Using a brass bar and hammer, tap out the rear tapered roller bearing (outer) from the carrier.
    If the bearing is damaged during removal, replace it.


22. REMOVE DIFFERENTIAL RING GEAR

  1. C237337E01
    Place matchmarks on the ring gear and differential case.
    Text in Illustration 
    *1
    Matchmark

  1. Using a screwdriver and hammer, pry out the staked portions of the lock plates.

  1. Remove the 10 ring gear set bolts and 5 lock plates.

  1. C237338
    Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


23. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT
If the ring gear runout is within the specified value (refer to the "Inspect Runout of Differential Ring Gear" procedure above), skip this step.
  1. Install the rear differential case bearings (outer) to the differential case.

  1. Install the differential case to the differential carrier.

  1. Install the 2 adjusting nuts.

  1. Install the 2 bearing caps to the differential carrier with the 4 bolts.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }

  1. C236665
    Using a dial indicator, measure the differential case runout.

    Maximum runout:
    0.07 mm (0.00276 in.)

  1. Remove the 4 bolts and 2 bearing caps.

  1. Remove the 2 adjusting nuts.

  1. Remove the differential case.

  1. Remove the rear differential case bearings (outer).


24. REMOVE REAR DIFFERENTIAL CASE BEARING

  1. C236666E01
    Using SST, remove the 2 bearings from the differential case.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)

    HINT:
    Do not remove the case bearings when not replacing the differential case.


25. DISASSEMBLE DIFFERENTIAL CASE

  1. C237340E01
    Place matchmarks on the LH and RH cases.
    Text in Illustration 
    *1
    Matchmark

  1. Remove the 8 bolts uniformly, a little at a time.

  1. C237341
    Using a plastic-faced hammer, tap out the LH case from the RH case.

  1. Remove the rear differential lock sleeve from the differential case LH.

  1. C237342E01
    Remove the following parts from the differential cases.
    1. (1) Side gear (2 pieces)
    2. (2) Side gear thrust washer (2 pieces)
    3. (3) Spider
    4. (4) Pinion gear (4 pieces)
    5. (5) Pinion gear thrust washer (4 pieces)


26. INSPECT REAR DIFFERENTIAL LOCK SLEEVE

  1. C237343
    Install the sleeve to the differential case LH and check that it moves smoothly.

  1. Install the sleeve to the side gear and check that it moves smoothly.


27. INSPECT SHIFT FORK AND SLEEVE

  1. C237344
    Using a feeler gauge, measure the clearance between the shift fork and sleeve.

    Standard clearance (reference):
    0.15 to 0.35 mm (0.00591 to 0.0137 in.)


28. INSPECT DIFFERENTIAL GEAR KIT
  1. Check that the differential pinion and differential side gear are not damaged.

    1. If the differential pinion or differential side gear is damaged, replace the differential gear kit.


29. INSPECT DIFFERENTIAL CASE
  1. Check that the differential case is not damaged.

    1. If the differential case is damaged, replace it.

← REMOVAL (from Jun 2011)REASSEMBLY (from Jun 2011) →