Attach the arm of SST to the diameter of the coil spring.
Text in Illustration
*a
Correct
*b
Incorrect
CAUTION:
Make sure that the coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.
Make sure that the claws of the hooks are securely attached.
Using SST, compress the coil spring.
CAUTION:
If the coil spring bends during the compression, immediately stop the compression and reinstall SST.
Do not compress the spring until the coil springs contact each other.
Do not use an impact wrench.
Install the coil spring to the shock absorber. Fit the lower end of the coil spring into the recess of the spring lower seat.
Text in Illustration
*a
Recess
2.
INSTALL FRONT COIL SPRING UPPER INSULATOR LH
Install the upper insulator to the shock absorber.
3.
INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY LH
Install the cushion retainer to the shock absorber.
Install the suspension support to the shock absorber.
4.
INSTALL FRONT SHOCK ABSORBER CUSHION
Install the cushion to the shock absorber.
5.
INSTALL FRONT SHOCK ABSORBER CUSHION RETAINER
Install the cushion retainer to the shock absorber.
6.
INSTALL FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT
Align the suspension support and absorber bushes as shown in the illustration.
Text in Illustration
*1
Suspension Support
*2
Absorber Bush
*a
for LH
*b
Front
*c
for RH
Install a new lock nut.
Torque:
18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
NOTICE:
Do not use an impact wrench. It will damage the shock absorber rod.
Release the coil spring while checking the position of the spring lower seat and suspension support.
7.
TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING
Install the shock absorber to the vehicle body so that: 1) the coil spring LH lower tip is facing away from the vehicle, and 2) the coil spring RH lower tip is facing toward the vehicle.
Using SST and 150 mm extension bar, install the 3 nuts to the upper side of the front shock absorber with coil spring.
SST
09249-B1010
Text in Illustration
*a
Fulcrum Length
Torque:
without SST:
40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
with SST:
28 N*m{
286 kgf*cm
, 21 ft.*lbf
}
HINT:
Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).
Temporarily install the bolt and nut as shown in the illustration.
HINT:
Fix the nut in place and temporarily install the bolt.
8.
INSTALL FRONT STABILIZER BAR
Install the stabilizer bar front to the vehicle body.
9.
INSTALL FRONT STABILIZER BRACKET
Install the 2 brackets with the 4 bolts.
Torque:
48 N*m{
489 kgf*cm
, 35 ft.*lbf
}
HINT:
2WD and 4WD and Pre-runner vehicle stabilizer brackets are imprinted with arrows. Only the 4WD and Pre-runner brackets' arrows must point toward the front of the vehicle.
10.
INSTALL FRONT STABILIZE LINK ASSEMBLY LH
Connect the stabilizer link to the lower arm with the nut.
Torque:
78 N*m{
795 kgf*cm
, 58 ft.*lbf
}
HINT:
If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.
11.
INSTALL FRONT STABILIZER LINK ASSEMBLY RH
HINT:
Use the same procedure described for the LH side.
12.
INSTALL FRONT WHEEL
Install the front wheel.
Torque:
for steel wheel:
152 N*m{
1550 kgf*cm
, 112 ft.*lbf
}
for aluminum wheel:
121 N*m{
1234 kgf*cm
, 89 ft.*lbf
}
13.
STABILIZE SUSPENSION
Lower the vehicle.
Press down on the vehicle several times to stabilize the suspension.