2014 Hilux · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built Apr 2012 – Jul 2012

Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. INSTALL FRONT COIL SPRING LH

  1. C159782E02
    Secure SST in a vise.
    SST
    09727-30021   (09727-00010, 09727-00021, 09727-00031)

  1. C275706E04
    Attach the arm of SST to the diameter of the coil spring.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

    CAUTION:
    1. Make sure that the coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.
    2. Make sure that the claws of the hooks are securely attached.

  1. Using SST, compress the coil spring.

    CAUTION:
    1. If the coil spring bends during the compression, immediately stop the compression and reinstall SST.
    2. Do not compress the spring until the coil springs contact each other.
    3. Do not use an impact wrench.

  1. F049913E02
    Install the coil spring to the shock absorber. Fit the lower end of the coil spring into the recess of the spring lower seat.
    Text in Illustration 
    *a
    Recess


2. INSTALL FRONT COIL SPRING UPPER INSULATOR LH
  1. Install the upper insulator to the shock absorber.


3. INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY LH
  1. Install the cushion retainer to the shock absorber.

  1. Install the suspension support to the shock absorber.


4. INSTALL FRONT SHOCK ABSORBER CUSHION
  1. Install the cushion to the shock absorber.


5. INSTALL FRONT SHOCK ABSORBER CUSHION RETAINER
  1. Install the cushion retainer to the shock absorber.


6. INSTALL FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

  1. C113158E02
    Align the suspension support and absorber bushes as shown in the illustration.
    Text in Illustration 
    *1
    Suspension Support
    *2
    Absorber Bush
    *a
    for LH
    *b
    Front
    *c
    for RH

  1. Install a new lock nut.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    Do not use an impact wrench. It will damage the shock absorber rod.

  1. Release the coil spring while checking the position of the spring lower seat and suspension support.


7. TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

F049915E01
  1. Install the shock absorber to the vehicle body so that: 1) the coil spring LH lower tip is facing away from the vehicle, and 2) the coil spring RH lower tip is facing toward the vehicle.

  1. C288511E01
    Using SST and 150 mm extension bar, install the 3 nuts to the upper side of the front shock absorber with coil spring.
    SST
    09249-B1010  
    Text in Illustration 
    *a
    Fulcrum Length

    Torque:
    without SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }
    with SST:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    HINT:
    Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

  1. F049906E02
    Temporarily install the bolt and nut as shown in the illustration.

    HINT:
    Fix the nut in place and temporarily install the bolt.


8. INSTALL FRONT STABILIZER BAR
  1. Install the stabilizer bar front to the vehicle body.


9. INSTALL FRONT STABILIZER BRACKET

F050282E02
  1. Install the 2 brackets with the 4 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    HINT:
    2WD and 4WD and Pre-runner vehicle stabilizer brackets are imprinted with arrows. Only the 4WD and Pre-runner brackets' arrows must point toward the front of the vehicle.


10. INSTALL FRONT STABILIZE LINK ASSEMBLY LH

C113157
  1. Connect the stabilizer link to the lower arm with the nut.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.


11. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


12. INSTALL FRONT WHEEL
  1. Install the front wheel.

    Torque:
    for steel wheel:
    152 N*m{ 1550 kgf*cm , 112 ft.*lbf }
    for aluminum wheel:
    121 N*m{ 1234 kgf*cm , 89 ft.*lbf }


13. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Press down on the vehicle several times to stabilize the suspension.


14. TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING
  1. Fix the nut in place and tighten the bolt.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    NOTICE:
    Do not tighten the nut.


15. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)
← INSTALLATION (Nov 2011 – Mar 2012)INSTALLATION (Aug 2012 – Jul 2013) →