2014 Hilux · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built Jun 2011 – Oct 2011

Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. INSTALL LOWER BALL JOINT ASSEMBLY

  1. C237856E01
    Using SST and press, press in a new lower ball joint.
    SST
    09226-10010  
    09631-32020  

  1. Install a new snap ring.

    NOTICE:
    Make sure the snap ring is securely installed in the groove.

  1. C237891E01
    Pack the upper ball joint with MP grease No. 2.
    Text in Illustration 
    *1
    MP Grease No. 2

    Grease capacity:
    8.0 g (0.282 oz.)

  1. Apply MP grease No. 2 to the locations shown in the illustration.

    NOTICE:
    Do not apply MP grease No. 2 to the tapered or threaded parts of the ball joint.

  1. Install a new dust cover to the lower arm.

  1. Install a new dust cover set ring.


2. INSTALL FRONT NO. 2 LOWER ARM BUSH

  1. F049931E02
    Using SST and a press, install a new bush.
    Text in Illustration 
    *a
    Bush Positioning Protrusion
    SST
    09710-20011   (09710-03081)
    09726-27012   (09726-02041)

    NOTICE:
    Press the bush while making sure the bush positioning protrusions are perpendicular to the lower arm as shown in the illustration.


3. INSTALL FRONT NO. 1 LOWER ARM BUSH

  1. F049930E01
    Using SST and a press, press in a new bush.
    SST
    09710-20011   (09710-06071)
    09710-22021   (09710-01071)


4. INSTALL FRONT LOWER BALL JOINT ATTACHMENT LH
  1. Install the ball joint attachment with the nut and a new cotter pin.

    Torque:
    140 N*m{ 1428 kgf*cm , 103 ft.*lbf }


5. TEMPORARILY INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

F049925E04
  1. Temporarily install the lower arm, and No. 1 and No. 2 camber adjusting cams with the 2 camber adjusting cams and 2 nuts.

    Text in Illustration 
    *1
    Matchmark

  1. Align the matchmarks on the No. 1 camber adjusting cam and No. 2 camber adjusting cam with the corresponding matchmarks on the vehicle frame.

  1. F049924E01
    Install the ball joint attachment with the 2 bolts.

    Torque:
    160 N*m{ 1632 kgf*cm , 118 ft.*lbf }


6. INSTALL FRONT SPRING BUMPER

  1. C237887E01
    Using SST, install the front spring bumper to the lower arm.
    SST
    09922-10010  

    Torque:
    for use without SST:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }
    for use with SST:
    23 N*m{ 231 kgf*cm , 17 ft.*lbf }

    HINT:
    1. Rotate SST in the direction shown in the illustration.
    2. Use a torque wrench with a fulcrum length of 345 mm (13.6 in.).


7. TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING
  1. Temporarily install the shock absorber with coil spring with the bolt and nut.


8. CONNECT FRONT STABILIZER LINK ASSEMBLY LH
  1. Connect the stabilizer link to the lower arm with the nut.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.


9. CONNECT FRONT SPEED SENSOR LH (w/ ABS)

  1. C187999E01
    Install the 2 harness clamps with the 2 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    NOTICE:
    1. When installing the clamp, do not twist the wire harness.
    2. Make sure the clamp rotation stopper touches the installation position.

  1. Install the speed sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.
    2. While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip.
    3. After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.
    4. When installing the sensor, do not twist the wire harness.

  1. C188000E01
    Install the harness clamp with the bolt.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    NOTICE:
    1. When installing the clamp, do not twist the wire harness.
    2. Make sure the clamp rotation stopper touches the installation position.

  1. C189975E01
    Install the harness clamp with the bolt.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    NOTICE:
    1. When installing the clamp, do not twist the wire harness.
    2. Make sure the clamp rotation stopper touches the installation position.

  1. Attach the clamp.

  1. Connect the connector.

    C188015E01

    NOTICE:
    1. Do not attach the connector to the radiator fan shroud before connecting the connector.
    2. Securely connect the connector.

  1. Attach the 2 clamps and the connector.

    NOTICE:
    When attaching the clamps, do not twist the wire harness.


10. INSTALL FRONT WHEEL

Torque:
152 N*m{ 1,550 kgf*cm , 112 ft.*lbf } for steel type
121 N*m{ 1,234 kgf*cm , 89 ft.*lbf } for aluminum type


11. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Press down on the vehicle several times to stabilize the suspension.


12. TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH
  1. Tighten the 2 nuts.

    Torque:
    210 N*m{ 2141 kgf*cm , 155 ft.*lbf }


13. TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING
  1. Fix the nut in place and tighten the bolt.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    NOTICE:
    Do not tighten the nut.


14. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)
← INSPECTION (from Jun 2011)INSTALLATION (Nov 2011 – Mar 2012) →