2014 Hilux · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built from Jun 2011

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. REMOVE FRONT WHEEL

2. REMOVE FRONT SPEED SENSOR LH (w/ ABS)

  1. Disconnect the connector.

    C188015E01

  1. Detach the 2 clamps and the connector.

  1. C189975E01
    Detach the clamp and remove the bolt and harness clamp.

  1. C188000E01
    Remove the bolt and harness clamp.

  1. C187999E01
    Remove the 3 bolts, 2 harness clamps and speed sensor.

    NOTICE:
    Keep the sensor tip and sensor installation hole free from foreign matter.


3. DISCONNECT FRONT SHOCK ABSORBER WITH COIL SPRING

F049906E03
  1. Remove the nut and bolt.

    HINT:
    While fixing the nut in place, loosen and remove the bolt.

  1. Disconnect the shock absorber with coil spring from the lower arm.


4. DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

  1. C113157
    Remove the nut and disconnect the stabilizer link from the lower arm.

    HINT:
    If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.


5. REMOVE FRONT SPRING BUMPER

  1. C237886E01
    Using SST, remove the front spring bumper.
    Text in Illustration 
    *a
    Turn
    SST
    09922-10010  

    NOTICE:
    Rotate SST in the direction shown in the illustration.


6. REMOVE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

F049924E01
  1. Remove the 2 bolts, and disconnect the ball joint attachment from the steering knuckle.

  1. F049925E04
    Place matchmarks on the No. 1 camber adjusting cam and vehicle frame, and No. 2 camber adjusting cam and vehicle frame.
    Text in Illustration 
    *1
    Matchmark

  1. Remove the 2 nuts, No. 1 and No. 2 camber adjusting cams, 2 camber adjusting cams and lower arm.


7. REMOVE FRONT LOWER BALL JOINT ATTACHMENT LH

  1. F049926E01
    Remove the cotter pin and nut.

  1. Using SST, remove the ball joint attachment.

    SST
    09628-00011  


8. REMOVE FRONT NO. 1 LOWER ARM BUSH

  1. F049927E01
    Using a hammer and chisel, strike and bend the entire flange of the bush as shown in the illustration.

  1. F049928E01
    Using SST, and a press, press out the bush.
    SST
    09632-36010  
    09950-00020  
    09950-60010   (09951-00520)


9. REMOVE FRONT NO. 2 LOWER ARM BUSH

  1. F049927E01
    Using a hammer and chisel, strike and bend the entire flange of the bush as shown in the illustration.

  1. F049928E01
    Using SST and a press, press out the bush.
    SST
    09632-36010  
    09950-00020  
    09950-60010   (09951-00520)


10. REMOVE LOWER BALL JOINT ASSEMBLY

  1. C237854E01
    Using 2 screwdrivers and a hammer, remove the snap ring.
    Text in Illustration 
    *a
    Protective tape

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the dust cover set ring and dust cover from the lower arm.

  1. C237855E01
    Using SST, remove the ball joint.
    Text in Illustration 
    *a
    Hold
    *b
    Turn
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04031, 09957-04010, 09958-04011)
    09710-22021   (09710-01081)

← ON-VEHICLE INSPECTION (from Jun 2011)INSPECTION (from Jun 2011) →