2014 Hilux · Service Manual BODY

TERMINALS OF ECU

System information · Vehicles built from Jun 2011


CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (except Double Cab, w/o Jam Protection)
  1. *1: for LHD
  2. *2: for RHD
  3. *3: w/o Regulator
  4. *4: w/ Regulator

  1. B290646E01
    Disconnect the P4 power window regulator master switch assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    P4-9 (B) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch off
    Below 1 V
    P4-9 (B) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    P4-1 (E) - Body ground*1
    P4-10 (E) - Body ground*2
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the P4 power window regulator master switch assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    P4-3 (U) - P4-1 (E)*1
    P4-2 (U) - P4-10 (E)*2
    R - W-B*1
    B - W-B*2
    1. Front power window regulator motor assembly (for driver side) up output*3
    2. Front door window regulator sub-assembly (for driver side) up output*4
    Ignition switch ON, driver side power window switch off → up
    Below 1 V → 11 to 14 V
    P4-4 (D) - P4-1 (E)*1
    P4-5 (D) - P4-10 (E)*2
    L-R - W-B
    1. Front power window regulator motor assembly (for driver side) down output*3
    2. Front door window regulator sub-assembly (for driver side) down output*4
    Ignition switch ON, driver side power window switch off → down (manual operation)
    Below 1 V → 11 to 14 V
    Ignition switch ON, driver side power window fully closed → driver side power window switch down (auto operation) → driver side power window fully open
    Below 1 V → 11 to 14 V → Below 1 V
    P4-8 (U) - P4-1 (E)*1
    P4-8 (U) - P4-10 (E)*2
    R-L - W-B
    1. Front power window regulator motor assembly (for front passenger side) up output*3
    2. Front door window regulator sub-assembly (for front passenger side) up output*4
    1. Window lock switch off
    2. Ignition switch ON, front passenger side power window remote manual switch off → up
    Below 1 V → 11 to 14 V
    P4-10 (D) - P4-1 (E)*1
    P4-1 (D) - P4-10 (E)*2
    G-W - W-B
    1. Front power window regulator motor assembly (for front passenger side) down output*3
    2. Front door window regulator sub-assembly (for front passenger side) down output*4
    1. Window lock switch off
    2. Ignition switch ON, front passenger side power window remote manual switch off → down
    Below 1 V → 11 to 14 V
    If the result is not as specified, the master switch may have a malfunction.


CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Double Cab, w/o Jam Protection)
  1. *1: for LHD
  2. *2: for RHD
  3. *3: w/o Regulator
  4. *4: w/ Regulator

  1. B276285E12
    Disconnect the P4 power window regulator master switch assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    P4-6 (B) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch off
    Below 1 V
    P4-6 (B) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    P4-3 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the P4 power window regulator master switch assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    P4-4 (U) - P4-3 (E)
    R - W-B*1
    B - W-B*2
    1. Front power window regulator motor assembly (for driver side) up output*3
    2. Front door window regulator sub-assembly (for driver side) up output*4
    Ignition switch ON, driver side power window switch off → up
    Below 1 V → 11 to 14 V
    P4-9 (D) - P4-3 (E)
    L-R - W-B
    1. Front power window regulator motor assembly (for driver side) down output*3
    2. Front door window regulator sub-assembly (for driver side) down output*4
    Ignition switch ON, driver side power window switch off → down (manual operation)
    Below 1 V → 11 to 14 V
    Ignition switch ON, driver side power window fully closed → driver side power window switch down (auto operation) → driver side power window fully open
    Below 1 V → 11 to 14 V → Below 1 V
    P4-18 (U) - P4-3 (E)*1
    P4-10 (U) - P4-3 (E)*2
    R-L - W-B
    1. Front power window regulator motor assembly (for front passenger side) up output*3
    2. Front door window regulator sub-assembly (for front passenger side) up output*4
    1. Window lock switch off
    2. Ignition switch ON, front passenger side power window remote manual switch off → up
    Below 1 V → 11 to 14 V
    P4-15 (D) - P4-3 (E)*1
    P4-13 (D) - P4-3 (E)*2
    G-W - W-B
    1. Front power window regulator motor assembly (for front passenger side) down output*3
    2. Front door window regulator sub-assembly (for front passenger side) down output*4
    1. Window lock switch off
    2. Ignition switch ON, front passenger side power window remote manual switch off → down
    Below 1 V → 11 to 14 V
    P4-12 (U) - P4-3 (E)*1
    P4-18 (U) - P4-3 (E)*2
    R-Y - W-B
    1. Rear power window regulator motor assembly LH up output*3
    2. Rear door window regulator sub-assembly LH up output*4
    1. Window lock switch off
    2. Ignition switch ON, rear power window LH remote manual switch off → up
    Below 1 V → 11 to 14 V
    P4-13 (D) - P4-3 (E)*1
    P4-12 (D) - P4-3 (E)*2
    G-Y - W-B
    1. Rear power window regulator motor assembly LH down output*3
    2. Rear door window regulator sub-assembly LH down output*4
    1. Window lock switch off
    2. Ignition switch ON, rear power window LH remote manual switch off → down
    Below 1 V → 11 to 14 V
    P4-10 (U) - P4-3 (E)*1
    P4-16 (U) - P4-3 (E)*2
    R-B - W-B
    1. Rear power window regulator motor assembly RH up output*3
    2. Rear door window regulator sub-assembly RH up output*4
    1. Window lock switch off
    2. Ignition switch ON, rear power window RH remote manual switch off → up
    Below 1 V → 11 to 14 V
    P4-16 (D) - P4-3 (E)*1
    P4-15 (D) - P4-3 (E)*2
    G-B - W-B
    1. Rear power window regulator motor assembly RH down output*3
    2. Rear door window regulator sub-assembly RH down output*4
    1. Window lock switch off
    2. Ignition switch ON, rear power window RH remote manual switch off → down
    Below 1 V → 11 to 14 V
    If the result is not as specified, the master switch may have a malfunction.


CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Jam Protection)
  1. *1: for LHD
  2. *2: for RHD
  3. *3: w/o Regulator
  4. *4: w/ Regulator
  5. *5: for Double Cab
  6. *6: except Double Cab

  1. B276285E12
    Disconnect the P4 power window regulator master switch assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    P4-6 (B) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch off
    Below 1 V
    P4-6 (B) - Body ground
    L - Body ground
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    P4-7 (BW) - Body ground
    L-B - Body ground
    Regulator motor power supply
    Always
    11 to 14 V
    P4-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    P4-2 (GND) - Body ground
    L-O - Body ground
    Ground
    Always
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the P4 power window regulator master switch assembly connector.

  4. Reset the front power window regulator motor assembly (for driver side)*3 or front door window regulator sub-assembly (for driver side)*4 (Click here).

  5. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    P4-4 (U) - P4-1 (E)
    R - W-B*1
    B - W-B*2
    1. Front power window regulator motor assembly (for driver side) up output*3
    2. Front door window regulator sub-assembly (for driver side) up output*4
    Ignition switch ON, driver side power window switch off → up (manual operation)
    Below 1 V → 11 to 14 V
    Ignition switch ON, driver side power window fully open → driver side power window switch up (auto operation) → driver side power window fully closed
    Below 1 V → 11 to 14 V → Below 1 V
    P4-9 (D) - P4-1 (E)
    L-R - W-B
    1. Front power window regulator motor assembly (for driver side) down output*3
    2. Front door window regulator sub-assembly (for driver side) down output*4
    Ignition switch ON, driver side power window switch off → down (manual operation)
    Below 1 V → 11 to 14 V
    Ignition switch ON, driver side power window fully closed → driver side power window switch down (auto operation) → driver side power window fully open
    Below 1 V → 11 to 14 V → Below 1 V
    P4-13 (U) - P4-1 (E)
    R-L - W-B
    1. Front power window regulator motor assembly (for front passenger side) up output*3
    2. Front door window regulator sub-assembly (for front passenger side) up output*4
    1. Window lock switch off
    2. Ignition switch ON, front passenger side power window remote manual switch off → up
    Below 1 V → 11 to 14 V
    P4-15 (D) - P4-1 (E)
    G-W - W-B
    1. Front power window regulator motor assembly (for front passenger side) down output*3
    2. Front door window regulator sub-assembly (for front passenger side) down output*4
    1. Window lock switch off
    2. Ignition switch ON, front passenger side power window remote manual switch off → down
    Below 1 V → 11 to 14 V
    P4-12 (U) - P4-1 (E)*5
    R-Y - W-B
    1. Rear power window regulator motor assembly LH up output*3
    2. Rear door window regulator sub-assembly LH up output*4
    1. Window lock switch off
    2. Ignition switch ON, rear power window LH remote manual switch off → up
    Below 1 V → 11 to 14 V
    P4-10 (D) - P4-1 (E)*5
    G-Y - W-B
    1. Rear power window regulator motor assembly LH down output*3
    2. Rear door window regulator sub-assembly LH down output*4
    1. Window lock switch off
    2. Ignition switch ON, rear power window LH remote manual switch off → down
    Below 1 V → 11 to 14 V
    P4-18 (U) - P4-1 (E)*5
    R-B - W-B
    1. Rear power window regulator motor assembly RH up output*3
    2. Rear door window regulator sub-assembly RH up output*4
    1. Window lock switch off
    2. Ignition switch ON, rear power window RH remote manual switch off → up
    Below 1 V → 11 to 14 V
    P4-16 (D) - P4-1 (E)*5
    G-B - W-B
    1. Rear power window regulator motor assembly RH down output*3
    2. Rear door window regulator sub-assembly RH down output*4
    1. Window lock switch off
    2. Ignition switch ON, rear power window RH remote manual switch off → down
    Below 1 V → 11 to 14 V
    P4-3 (VCC) - P4-2 (GND)*5
    P4-10 (VCC) - P4-2 (GND)*6
    BR - L-O
    Power window regulator motor sensor power source
    Ignition switch ON, driver side power window switch off → up or down
    Below 1 V → 11 to 14 V
    P4-14 (PLS) - Body ground*5
    P4-11 (PLS) - Body ground*6
    P-G - Body ground
    1. Front power window regulator motor assembly (for driver side) up or down output*3
    2. Front door window regulator sub-assembly (for driver side) up or down output*4
    Ignition switch ON, driver side power window switch off → up or down
    Pulse waveform is output
    P4-17 (PLS2) - Body ground*5
    P4-14 (PLS2) - Body ground*6
    B - Body ground
    1. Front power window regulator motor assembly (for driver side) up or down output*3
    2. Front door window regulator sub-assembly (for driver side) up or down output*4
    Ignition switch ON, driver side power window switch off → up or down
    Pulse waveform is output
    If the result is not as specified, the master switch may have a malfunction.

← PROBLEM SYMPTOMS TABLE (from Aug 2013)Auto Up / Down Function does not Operate (Jun 2011 – Jul 2013) →