2014 Hilux · Service Manual BODY

Auto Up / Down Function does not Operate

Circuit diagnosis · Vehicles built Jun 2011 – Jul 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013

DESCRIPTION

If the auto up/down function does not operate, the cause may be one or more of the following:
  1. The recorded power window fully closed position, which is stored in the power window regulator master switch assembly, was erased as a result of: 1) the PWR H-fuse or DOOR fuse being replaced; or 2) the battery cable and the master switch's connector being disconnected.
  2. The power window regulator master switch assembly has a malfunction.
  3. The pulse sensors in the front power window regulator motor assembly (for driver side)*1 or front door window regulator sub-assembly*2 have a malfunction.
  4. The wiring between the power window regulator master switch assembly and the front power window regulator motor assembly (for driver side)*1 or front door window regulator sub-assembly*2 is open or short-circuited.
  1. *1: w/o Regulator
  2. *2: w/ Regulator

WIRING DIAGRAM

B280492E04

INSPECTION PROCEDURE


1. CHECK MANUAL UP/DOWN FUNCTION (FOR DRIVER SIDE)
  1. Check that the manual up/down function operates normally.

    OK:
    Manual up/down function operates normally.



NG
GO TO DRIVER SIDE POWER WINDOW MANUAL FUNCTION DOES NOT OPERATE WITH POWER WINDOW MASTER SWITCH (Click here)
OK


2. CHECK LIGHT OF POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

  1. Turn the ignition switch ON.B277627E02

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *1
    AUTO Light
    -
    -

  1. Operate the master switch's driver side power window switch for 2 seconds or more.

  1. Check the blinking pattern of the AUTO light. Compare the blinking pattern with the illustration.B278579E01

    Result 
    Blinking Pattern
    Proceed to
    1 or 3
    A
    2
    B
    4
    C



B
Go to step 4

C
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
A


3. RESET FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER SIDE) OR FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR DRIVER SIDE)
  1. Check that the power window operates normally after reset (Click here).

    OK:
    Power window operates normally.



NG
Go to step 4
OK

END

4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR [FOR DRIVER SIDE] OR FRONT DOOR WINDOW REGULATOR [FOR DRIVER SIDE])
  1. *1: for LHD
  2. *2: for RHD
  3. *3: for Double Cab
  4. *4: except Double Cab
  1. Disconnect the P4 power window regulator master switch assembly connector.

  1. w/o Regulator:

    1. Disconnect the P5*1 or P6*2 front power window regulator motor assembly (for driver side) connector.

  1. w/ Regulator:

    1. Disconnect the P5*1 or P6*2 front door window regulator sub-assembly (for driver side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    P4-3 (VCC) - P5-4 (SSRB)*3
    P4-10 (VCC) - P5-4 (SSRB)*4
    Always
    Below 1 Ω
    P4-14 (PLS) - P5-5 (PLS)*3
    P4-11 (PLS) - P5-5 (PLS)*4
    Always
    Below 1 Ω
    P4-17 (PLS2) - P5-3 (PLS2)*3
    P4-14 (PLS2) - P5-3 (PLS2)*4
    Always
    Below 1 Ω
    P4-2 (GND) - P5-6 (E)
    Always
    Below 1 Ω
    P4-3 (VCC) or P5-4 (SSRB) - Body ground*3
    P4-10 (VCC) or P5-4 (SSRB) - Body ground*4
    Always
    10 kΩ or higher
    P4-14 (PLS) or P5-5 (PLS) - Body ground*3
    P4-11 (PLS) or P5-5 (PLS) - Body ground*4
    Always
    10 kΩ or higher
    P4-17 (PLS2) or P5-3 (PLS2) - Body ground*3
    P4-14 (PLS2) or P5-3 (PLS2) - Body ground*4
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    P4-3 (VCC) - P6-4 (SSRB)*3
    P4-10 (VCC) - P6-4 (SSRB)*4
    Always
    Below 1 Ω
    P4-14 (PLS) - P6-5 (PLS)*3
    P4-11 (PLS) - P6-5 (PLS)*4
    Always
    Below 1 Ω
    P4-17 (PLS2) - P6-3 (PLS2)*3
    P4-14 (PLS2) - P6-3 (PLS2)*4
    Always
    Below 1 Ω
    P4-2 (GND) - P6-6 (E)
    Always
    Below 1 Ω
    P4-3 (VCC) or P6-4 (SSRB) - Body ground*3
    P4-10 (VCC) or P6-4 (SSRB) - Body ground*4
    Always
    10 kΩ or higher
    P4-14 (PLS) or P6-5 (PLS) - Body ground*3
    P4-11 (PLS) or P6-5 (PLS) - Body ground*4
    Always
    10 kΩ or higher
    P4-17 (PLS2) or P6-3 (PLS2) - Body ground*3
    P4-14 (PLS2) or P6-3 (PLS2) - Body ground*4
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (PLS, PLS2 SIGNAL)

  1. B276285E14
    Remove the power window regulator master switch assembly with its connectors still connected.

  1. Using an oscilloscope, check the waveform.

    OK:
    for Double Cab 
    Tester Connection
    Switch Condition
    Specified Condition
    P4-14 (PLS) - Body ground
    Ignition switch ON, driver side power window switch off → up or down
    Pulse waveform is output
    P4-17 (PLS2) - Body ground
    Ignition switch ON, driver side power window switch off → up or down
    Pulse waveform is output
    except Double Cab 
    Tester Connection
    Switch Condition
    Specified Condition
    P4-11 (PLS) - Body ground
    Ignition switch ON, driver side power window switch off → up or down
    Pulse waveform is output
    P4-14 (PLS2) - Body ground
    Ignition switch ON, driver side power window switch off → up or down
    Pulse waveform is output

    Text in Illustration 
    *A
    for Double Cab
    *B
    except Double Cab
    *a
    Component with harness connected
    (Power Window Regulator Master Switch Assembly)
    Result 
    Result
    Proceed to
    NG
    A
    OK (w/o Regulator)
    B
    OK (w/ Regulator)
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER SIDE)

C
REPLACE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (FOR DRIVER SIDE)
A

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


← TERMINALS OF ECU (from Jun 2011)Auto Up / Down Function does not Operate (from Aug 2013) →