2014 Hilux · Service Manual INTRODUCTION

INITIALIZATION

Troubleshooting · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


PROCEDURES NECESSARY WHEN CABLE IS DISCONNECTED/RECONNECTED TO BATTERY TERMINAL
Procedures Necessary when Cable is Disconnected/Reconnected to Battery Terminal 
Necessary Procedure
Effect or Inoperative Function when Necessary Procedure is not Performed
See page
Circling calibration
Compass
Click here
Power window regulator motor initialization (for Driver Side, w/ Jam Protection)
  1. Jam protection function
  2. Power window control system
Click here

PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
Procedures Necessary when ECU or Other Parts are Replaced 
Replacement Part
Necessary Procedure
Effect or Inoperative Function when Necessary Procedure is not Performed
See page
ECM (for 1KD-FTV, w/ DPF)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
Engine assembly (for 1KD-FTV, w/ DPF)
  1. Clear crank time compensation data
  2. Injector compensation code registration
  3. Pilot quantity learning
Engine starting
Crankshaft position sensor plate (for 1KD-FTV, w/ DPF)
Clear crank time compensation data
Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data
Air Fuel ratio sensor (for 1KD-FTV, w/ DPF)
Clear A/F sensor compensation data
EGR volume is affected
Fuel supply pump (for 1KD-FTV, w/ DPF)
Supply pump initialization
Engine startability
DPF catalyst (for 1KD-FTV, w/ DPF)
  1. Clear DPF thermal deterioration data
  2. Learning values write
Even if catalytic converter is replaced with new one, catalyst record of DPF thermal deterioration stored in ECM is same as before replacement
Fuel injector (for 1KD-FTV, w/ DPF)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
Automatic transmission assembly, engine assembly or ECM (for 1KD-FTV, w/ DPF)
Automatic Transmission Initialization
Large shift shock
ECM (for 1KD-FTV, w/ EGR Cooler)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
Engine assembly (for 1KD-FTV, w/ EGR Cooler)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
Fuel supply pump (for 1KD-FTV, w/ EGR Cooler)
Supply pump initialization
Engine starting
Fuel injector (for 1KD-FTV, w/ EGR Cooler)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
ECM (for 1KD-FTV, w/o EGR Cooler)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
Engine assembly (for 1KD-FTV, w/o EGR Cooler)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
Fuel supply pump (for 1KD-FTV, w/o EGR Cooler)
Supply pump initialization
Engine startability
Fuel injector (for 1KD-FTV, w/o EGR Cooler)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
ECM (for 2KD-FTV, w/ DPF)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
Engine assembly (for 2KD-FTV, w/ DPF)
  1. Clear crank time compensation data
  2. Injector compensation code registration
  3. Pilot quantity learning
Engine starting
Crankshaft position sensor plate (for 2KD-FTV, w/ DPF)
Clear crank time compensation data
Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data
Air Fuel ratio sensor (for 2KD-FTV, w/ DPF)
Clear A/F sensor compensation data
EGR volume is affected
Fuel supply pump (for 2KD-FTV, w/ DPF)
Supply pump initialization
Engine startability
DPF catalyst (for 2KD-FTV, w/ DPF)
  1. Clear DPF thermal deterioration data
  2. Learning values write
Even if catalytic converter is replaced with new one, catalyst record of DPF thermal deterioration stored in ECM is same as before replacement
Fuel injector (for 2KD-FTV, w/ DPF)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
ECM (for 2KD-FTV, w/ EGR Cooler)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
Engine assembly (for 2KD-FTV, w/ EGR Cooler)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
Fuel supply pump (for 2KD-FTV, w/ EGR Cooler)
Supply pump initialization
Engine startability
Fuel injector (for 2KD-FTV, w/ EGR Cooler)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
ECM (for 2KD-FTV, w/o EGR Cooler)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
Engine assembly (for 2KD-FTV, w/o EGR Cooler)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
Fuel supply pump (for 2KD-FTV, w/o EGR Cooler)
Supply pump initialization
Engine startability
Fuel injector (for 2KD-FTV, w/o EGR Cooler)
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
for A750E
  1. Automatic transmission assembly
  2. ECM
  3. Engine assembly (for 1GR-FE)
Reset memory
Large shift shock
Click here
for A750F
  1. Automatic transmission assembly (for 1KD-FTV)
  2. Valve body assembly (for 1KD-FTV)
  3. Any of the shift solenoid valve (for 1KD-FTV)
Reset memory
Large shift shock
Click here
for A750F
  1. Automatic transmission assembly (for 1GR-FE)
  2. ECM (for 1GR-FE)
  3. Engine assembly (for 1GR-FE)
Reset memory
Large shift shock
Click here
Skid control ECU (Brake actuator assembly)
Yaw rate and acceleration sensor zero point calibration
VSC
Click here
  1. Yaw rate and acceleration sensor
  2. Front wheel alignment adjustment
  1. Clearing zero point calibration data
  2. Yaw rate and acceleration sensor zero point calibration
VSC
for Built-in Type Door Control Receiver
  1. Theft warning ECU assembly
  2. Key
Recognition code registration
Wireless door lock control system
Click here
for Non-built-in Type Door Control Receiver
  1. Door control receiver assembly
  2. Key
Recognition code registration
Wireless door lock control system
Click here
  1. Transponder key ECU assembly
  2. ECM
  3. Key
Code registration
Engine starting
Refer to the Service Bulletin for the registration procedure.
Timing belt (for 1KD-FTV, 2KD-FTV, 5L-E)
Mode reset operation
  1. Does not illuminate when replacement is necessary
  2. Illuminates when replacement is not necessary
Click here
for Driver Side, w/ Jam Protection
  1. Front door power window regulator sub-assembly (w/ Motor)
  2. Front power window regulator motor assembly (w/o Motor)
  3. Front door power window regulator sub-assembly (w/o Motor)
  4. Power window master switch
Motor initialization
  1. Jam protection function
  2. Power window control system
Click here
← INITIALIZATION (Jun 2011 – Jul 2012)INITIALIZATION (from Aug 2013) →