2014 Hilux · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built from Jun 2011

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart.


1. INSTALL FRONT AXLE HUB INNER BEARING

F049862E01
  1. Using SST and a press, press a new bearing into the steering knuckle.

    SST
    09527-17011  
    09950-60020   (09951-00910)

  1. Using snap ring pliers, install a new snap ring.


2. INSTALL FRONT AXLE HUB OIL SEAL

F049863E01
  1. Using SST and a plastic-faced hammer, tap in a new oil seal.

    SST
    09223-15030  
    09527-17011  

  1. Coat MP grease to the lip of the oil seal.


3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH

F049864E01
  1. Install the dust cover to the steering knuckle with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Using SST and a press, press in the axle hub to the steering knuckle.

    SST
    09223-00010  


4. INSTALL LOCK NUT AND ABS SPEED SENSOR ROTOR OR SPACER

F049769E01
  1. w/ ABS:
    Install the ABS speed sensor rotor.

  1. w/o ABS:
    Install the spacer.

  1. Install a new lock nut to the axle hub.

    Torque:
    199 N*m{ 2,029 kgf*cm , 147 ft.*lbf }

  1. Using a chisel and hammer, stake the lock nut.

    NOTICE:
    Do not scratch the serration of the speed sensor rotor.


5. INSTALL KNUCKLE GREASE RETAINER CAP

F049865E01
  1. Using a brass bar and hammer, install the knuckle grease retainer cap.

    NOTICE:
    Do not damage the knuckle grease retainer cap.


6. INSTALL FRONT AXLE HUB ASSEMBLY

7. CONNECT FRONT SUSPENSION UPPER ARM ASSEMBLY LH

C113713
  1. Connect the upper arm with the nut.

    Torque:
    110 N*m{ 1,122 kgf*cm , 81 ft.*lbf }

  1. Install a new clip.

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut an additional 60°.


8. CONNECT FRONT SUSPENSION LOWER ARM ASSEMBLY WITH ATTACHMENT LH

F049765E01
  1. Connect the suspension arm with the 2 bolts.

    Torque:
    160 N*m{ 1,632 kgf*cm , 118 ft.*lbf }


9. CONNECT TIE ROD END SUB-ASSEMBLY

C113714
  1. Connect the tie rod end with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.


10. INSTALL FRONT DISC

11. INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH

F049868E01
  1. Install the brake cylinder with the 2 bolts.

    Torque:
    126 N*m{ 1,285 kgf*cm , 93 ft.*lbf }

  1. Connect the brake hose to the brake cylinder with the union bolt and a new gasket.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


12. INSTALL FRONT SPEED SENSOR LH

C113712
  1. Install the speed sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Connect the 3 clamps with the 3 bolts.


13. BLEED BRAKE LINE
  1. for TSAM Made:
    (Click here)

  1. for TMT Made:
    (Click here)

  1. w/ VSC:
    (Click here)


14. INSTALL FRONT WHEEL

Torque:
121 N*m{ 1,234 kgf*cm , 89 ft.*lbf } for aluminum type
152 N*m{ 1,550 kgf*cm , 112 ft.*lbf } for steel type

← REMOVAL (from Jun 2011)COMPONENTS (from Jun 2011) →