2014 Hilux · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Jun 2011 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL FRONT AXLE HUB ASSEMBLY

F042759E01
  1. Apply MP grease to a new O-ring.

  1. Install the new O-ring to the axle hub.

  1. Install the dust cover and axle hub to the steering knuckle with the 4 bolts.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }


2. INSTALL FRONT AXLE HUB DUST SEAL (for 4WD)

F042767E01
  1. Using SST and a press, press in a new dust seal.

    SST
    09527-17011  
    09950-70010   (09951-07100)
    09951-01000  


3. INSTALL KNUCKLE GREASE RETAINER CAP LH (for Pre-Runner)

F042765E01
  1. Using a brass bar and hammer, install a new retainer cap.

    NOTICE:
    Do not damage the retainer cap.


4. CONNECT FRONT SUSPENSION UPPER ARM ASSEMBLY LH

F043605E01
  1. Connect the upper arm with the nut.

    Torque:
    110 N*m{ 1,122 kgf*cm , 81 ft.*lbf }

  1. Install a new clip.

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut an additional 60°.


5. CONNECT FRONT SUSPENSION LOWER ARM ASSEMBLY WITH ATTACHMENT LH

F050870E01
  1. Connect the suspension arm with the 2 bolts.

    Torque:
    160 N*m{ 1,632 kgf*cm , 118 ft.*lbf }


6. CONNECT TIE ROD END SUB-ASSEMBLY LH

C113718
  1. Connect the tie rod end with the nut.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.


7. CONNECT FRONT STABILIZER LINK ASSEMBLY LH

C099158E01
  1. Connect the stabilizer link with the nut.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.


8. INSTALL FRONT AXLE HUB NUT (for 4WD)

F042732E01
  1. Install the hub nut.

    Torque:
    235 N*m{ 2,396 kgf*cm , 173 ft.*lbf }

  1. Install the adjusting cap and a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.


9. INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)
  1. Install a new grease cap to the axle hub.


10. INSTALL FRONT DISC

11. INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH

F050211E01
  1. Install the disc brake cylinder with the 2 bolts.

    Torque:
    123 N*m{ 1,254 kgf*cm , 91 ft.*lbf }

  1. F042731E01
    Install the brake tube bracket to the steering knuckle with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. F051151E01
    Using SST, connect the brake tube to the disc brake cylinder.
    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf } for use without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } for use with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).


12. INSTALL SPEED SENSOR FRONT LH

C113715
  1. Install the speed sensor with the bolt.

  1. Connect the 2 clamps.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Install the speed sensor wire harness to the steering knuckle with the bolt.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }


13. BLEED BRAKE LINE
  1. for TSAM Made:
    (Click here)

  1. for TMT Made:
    (Click here)

  1. w/ VSC:
    (Click here )


14. INSTALL FRONT WHEEL

Torque:
105 N*m{ 1,071 kgf*cm , 77 ft.*lbf }

← INSTALLATION (Jun 2011 – Jul 2013)INSTALLATION (from Aug 2014) →