INSTALLATION
Removal / installation · Vehicles built Jun 2011 – Jul 2013
Versions by build date: Jun 2011 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
- HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
- A bolt without a torque specification is shown in the standard bolt chart (Click here).
| 1.
INSTALL FRONT AXLE HUB ASSEMBLY |
 |
Apply MP grease to a new O-ring.
Install the new O-ring to the axle hub.
Install the dust cover and axle hub to the steering knuckle with the 4 bolts.
-
Torque:
- 80 N*m{
816 kgf*cm
, 59 ft.*lbf
}
| 2.
INSTALL FRONT AXLE HUB DUST SEAL (for 4WD) |
 |
Using SST and a press, press in a new dust seal.
- SST
- 09527-17011
09950-70010
(09951-07100)
09951-01000
| 3.
INSTALL KNUCKLE GREASE RETAINER CAP LH (for Pre-Runner) |
 |
Using a brass bar and hammer, install a new retainer cap.
- NOTICE:
- Do not damage the retainer cap.
| 4.
CONNECT FRONT SUSPENSION UPPER ARM ASSEMBLY LH |
 |
Connect the upper arm with the nut.
-
Torque:
- 110 N*m{
1,122 kgf*cm
, 81 ft.*lbf
}
Install a new clip.
- NOTICE:
- If the holes for the clip are not aligned, tighten the nut an additional 60°.
| 5.
CONNECT FRONT SUSPENSION LOWER ARM ASSEMBLY WITH ATTACHMENT LH |
 |
Connect the suspension arm with the 2 bolts.
-
Torque:
- 160 N*m{
1,632 kgf*cm
, 118 ft.*lbf
}
| 6.
CONNECT TIE ROD END SUB-ASSEMBLY LH |
 |
Connect the tie rod end with the nut.
-
Torque:
- 91 N*m{
928 kgf*cm
, 67 ft.*lbf
}
Install a new cotter pin.
- NOTICE:
- If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.
| 7.
CONNECT FRONT STABILIZER LINK ASSEMBLY LH |
 |
Connect the stabilizer link with the nut.
-
Torque:
- 70 N*m{
714 kgf*cm
, 52 ft.*lbf
}
- HINT:
- If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.
| 8.
INSTALL FRONT AXLE HUB NUT (for 4WD) |
 |
Install the hub nut.
-
Torque:
- 235 N*m{
2,396 kgf*cm
, 173 ft.*lbf
}
Install the adjusting cap and a new cotter pin.
- NOTICE:
- If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.
| 9.
INSTALL FRONT AXLE HUB GREASE CAP (for 4WD) |
 |
Install a new grease cap to the axle hub.
| 11.
INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH |
 |
Install the disc brake cylinder with the 2 bolts.
-
Torque:
- 123 N*m{
1,254 kgf*cm
, 91 ft.*lbf
}
- Install the brake tube bracket to the steering knuckle with the bolt.
-
Torque:
- 29 N*m{
296 kgf*cm
, 21 ft.*lbf
}
- Using SST, connect the brake tube to the disc brake cylinder.
- SST
- 09023-00101
-
Torque:
- 15 N*m{
155 kgf*cm
, 11 ft.*lbf
}
for use without SST
- 14 N*m{
143 kgf*cm
, 10 ft.*lbf
}
for use with SST
- HINT:
- Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
| 12.
INSTALL SPEED SENSOR FRONT LH |
 |
Install the speed sensor with the bolt.
Connect the 2 clamps.
-
Torque:
- 8.5 N*m{
87 kgf*cm
, 75 in.*lbf
}
Install the speed sensor wire harness to the steering knuckle with the bolt.
-
Torque:
- 32 N*m{
326 kgf*cm
, 24 ft.*lbf
}
| 13.
BLEED BRAKE LINE |
 |
for TSAM Made:
(Click here)
for TMT Made:
(Click here)
w/ VSC:
(Click here )
| 14.
INSTALL FRONT WHEEL |
 |
-
Torque:
- 105 N*m{
1,071 kgf*cm
, 77 ft.*lbf
}