2014 Hilux · Service Manual BODY ELECTRICAL

Seat Belt Warning Light for Passenger Seat does not Flash

Circuit diagnosis · Vehicles built from Jun 2011

WIRING DIAGRAM

E115294E19
E115294E20

INSPECTION PROCEDURE


1. INSPECT FUSE (ECU-IG & GAUGE)
  1. Remove the ECU-IG&GAUGE fuse from the instrument panel junction block (driver side junction block).

  1. Measure the resistance of the fuse.

    Standard Resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2. CHECK HARNESS AND CONNECTOR (METER*1 OR LIGHT*2 - BATTERY AND GROUND)
  1. Disconnect the A27*1 meter connector.

  1. Disconnect the P13*2 light connector.

  1. 1: w/ Accessory Meter Assembly
  2. 2: w/o Accessory Meter Assembly
  1. Measure the voltage of the wire harness side connector.

    Standard Voltage:
    w/ Accessory Meter Assembly 
    Tester Connection
    Condition
    Specified Condition
    A27-12 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch OFF
    Below 1 V

    w/o Accessory Meter Assembly:
    Tester Connection
    Condition
    Specified Condition
    P13-3 - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch OFF
    Below 1 V

  1. Measure the resistance of the wire harness side connector.

    Standard Resistance:
    w/ Accessory Meter Assembly  
    Tester Connection
    Specified Condition
    A27-1 (GND1) - Body ground
    Below 1 Ω

    w/o Accessory Meter Assembly:
    Tester Connection
    Specified Condition
    P13-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT FRONT SEAT INNER BELT ASSEMBLY (BUCKLE SWITCH)
E111664E03
  1. Disconnect the F17 belt connector.

  1. Measure the resistance of the buckle switch.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Seat belt is unfastened (ON) and apply more than 147 N (15 kgf, 22 lbf) of force to occupant detection sensor
    Below 1 Ω
    Seat belt is fastened (OFF)
    1 MΩ or higher



NG
Go to step 6
OK


4. CHECK HARNESS AND CONNECTOR (INNER BELT - BODY GROUND)
E117164E05
  1. Disconnect the F17 belt connector.

  1. Measure the resistance of the wire harness side connector.

    Standard Resistance:
    Tester Connection
    Specified Condition
    F17-2 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (INNER BELT - METER*1 OR LIGHT*2)
  1. Disconnect the F17 belt connector.

  1. Disconnect the A27*1 meter connector.

  1. Disconnect the P13*2 light connector.

  1. *1: w/ Accessory Meter Assembly
  2. *2: w/o Accessory Meter Assembly
  1. Measure the resistance of the wire harness side connectors.

    Standard Resistance:
    w/ Accessory Meter Assembly 
    Tester Connection
    Specified Condition
    F17-1 - A27-8 (PBEW)
    Below 1 Ω

    w/o Accessory Meter Assembly:
    Tester Connection
    Specified Condition
    F17-1 - P13-3
    Below 1 Ω

Result 
Result
Proceed to
OK (w/ Accessory Meter Assembly)
A
OK (w/o Accessory Meter Assembly)
B
NG
C


B
REPLACE PASSENGER SEAT BELT WARNING LIGHT

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ACCESSORY METER ASSEMBLY (MULTI-DISPLAY)

6. INSPECT FRONT SEAT INNER BELT ASSEMBLY (OCCUPANT DETECTION SENSOR)
E076458E04
  1. Disconnect the A sensor connector.

  1. Measure the resistance of the sensor.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Apply more than 147 N (15 kgf, 22 lbf) of force to occupant detection sensor
    Below 100 Ω
    No force applied to occupant detection sensor
    1 MΩ or higher



NG
REPAIR FRONT SEAT CUSHION PAD
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR PASSENGER SIDE)


← Driver Side Seat Belt Warning Light does not Operate (from Jun 2011)COMPONENTS (from Jun 2011) →