2014 Hilux · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. INSTALL SHOULDER BELT ANCHORAGE PLATE COVER (for Double Cab)

B084925E05
  1. Install the plate cover as shown in the illustration.

    HINT:
    Make sure the plate cover is firmly set into the garnish's claws.


2. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY (for Extra Cab and Double Cab)

B084924E02
  1. Insert the tip of the adjuster to the pillar, and align the adjuster's bolt hole to the pillar's bolt hole.

  1. Install the bolt as shown in the illustration.

    Torque:
    42:
    N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the center pillar garnish (Click here).

  1. Install the quarter pillar garnish (Click here ).


3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

B084917E01

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner single cab and extra cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B084922E01
    w/o Pretensioner Double cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf }

  1. B113098E03
    w/ Pretensioner:
    Install the bolt and seat belt.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B

  1. B114993
    w/ Pretensioner:
    Connect the pretensioner connector as shown in the illustration.

  1. B084915E01
    Single cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Close the cover.

  1. B084920E01
    Extra cab and double cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the cap.

  1. B085691E01
    Single cab:
    Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B085692E01
    Extra cab:
    Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B085693E01
    Double cab:
    Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSTALLATION (Jun 2011 – Jul 2012)INSTALLATION (from Aug 2013) →